Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > BMW Tech
BMW Tech BMW Tech Forum - For Questions specific and of interest to BMW riders only.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 23 Jan 2005
AliBaba's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Apr 2001
Location: Norway
Posts: 1,379
Siebenrock

The pistons on my R80GS basic are worn and some of the cooling-fins have broken so it’s time for some work.

Siebenrock have a “power-kit” (new cylinders and pistons) which increases the power with 20% and torque with 30%.
Is there anybody who has tried it? Experiences on low-octane fuel? (Compression is increased to 9.5)

There is also an “enduro-camshaft”, 296°, any thoughts?
Reply With Quote
  #2  
Old 23 Jan 2005
Gold Member
Veteran HUBBer
 
Join Date: Oct 2004
Location: Germany
Posts: 241
Hi AliBaba,

I have no personal experience with those parts, but my impression is that especially the power kit is quite popular in Germany.

Try http://www.boxer-forum.de/dc/dcboard...topics&forum=6

Although a german-speaking forum, I am quit confident that you will get advise if you post in english.

Regards

Lars
Reply With Quote
  #3  
Old 24 Jan 2005
Gold Member
Veteran HUBBer
 
Join Date: Mar 2001
Location: British Columbia
Posts: 246
I looked into this kit as well. The main advantage is that you don't have to change your carbs or heads, just bolt it together, get the jetting right, and away you go. I was told by one supplier that the high compression is a problem with low octane fuel. You would be looking at 93 or better octane, at least! This might be fine in Europe/ North America where such fuel is easy to find, but traveling abroad will be hampered.

My thought was to combine the 'power kit' with dual plugging of the heads (which spreads the flame better and reduces detonation). I was advised By Siebenrock that that would still not be adequate to run on 87 octane, and they would advise 91 minium even with the dual plugging.

A better option for travel is to get a proper 1000cc setup with heads and carbs to match. With dual plugging, lower octane fuel shouldn't be a problem.
Reply With Quote
  #4  
Old 24 Jan 2005
AliBaba's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Apr 2001
Location: Norway
Posts: 1,379
Thank you for replies!
I’ve already checked the German forums, loads of info!

Running on low octane fuel with high compression (9.5:1) is an issue, and I hoped to find someone who has tried it. (Ted Simon had some kind of 1000-conversion).
Hmm, I just saw that the compression on KTM Adventure is 11.7:1, the new XT660 has 10:1. Maybe they both have dual plugging?
The R1100GS had 10.3:1 and it was not dual plugged, but I guess other factors also are important. (Timing ++)
Unfortunately less then half of the bikes mileage is in areas with low octane petrol so it might be an option to use octane-booster or to reduce compression temporarily.


To build a standard BMW 1000 is out of question. The price is high and IMHO the R80 runs better then the R100 (much smoother), but I think the engine with Siebenrock 1000 kit runs much better then a standard R80. (I haven’t tried the 1042 and 1070 but they are way to expensive anyway).
Reply With Quote
  #5  
Old 24 Jan 2005
Vaufi's Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Jan 2004
Location: Munich, the beer capital
Posts: 1,047
Hi AliBaba,

I've reworked my GS80 with dual plugging and balancing my pistons & conrods. It doesn't go faster, but much smoother. Should be positive for engine life.
What I refrained from was to lift the compression because of the above mentioned probs. If you stay in Europe, ok, but if you want to visit other countries I would prefer to genuine BMW parts. You will find spares everywhere. I'm not sure whether Siebenrock is well known outside Europe.

Good luck,
Hans
__________________
Only when we pause to wonder
do we go beyond the limits of our little lives.
(Rod McKuen)
Reply With Quote
  #6  
Old 24 Jan 2005
Gold Member
Veteran HUBBer
 
Join Date: Mar 2001
Location: British Columbia
Posts: 246
I believe that Ted Simons bike was (is) an R80 GS basic (a 'parts bin special' combining G/S and GS pieces) with R100 barrels/ pistons/ heads added.

The Siebenrock claims smoother running then a standard R100 because the parts (pistons) are lighter = less reciprocating mass which reduces vibration, one of the reasons the R80 runs smoother.

I would say that sourcing a used R100 top end would not be that much more expensive then the Siebenrock kit. HPN has a reputation for very smooth running R100's in their rally and other special models. They balance the internals, which apparently makes a large difference, pointing to large manufacturing tolerances. Keep in mind that the this engine was designed in the late 60's and intended to be 600-750 cc's.
Reply With Quote
  #7  
Old 25 Jan 2005
AliBaba's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Apr 2001
Location: Norway
Posts: 1,379
Thanks for interesting replies!

Balancing the pistons and conrods will have a positive effect on enginelife, I might consider it.
When it comes to dualplugging I’m not sure. I totally agree on the principle but I don’t like the way the plugs are placed underneath the cylinderhead. For me it looks fragile and I already have a lot of scratches in that area.

Yes Ted Simon has a Basic (like mine). I’m not sure how he made the conversion to 1000cc.
After what I have heard you should change the carbs if you use BMW 1000cc cylinders. With second hand prices from Motorworks this will be almost 50% more expensive then a new Siebenrock-kit. There will also be some additional costs to overhaul the used pats (carbs, new rings, gudgeon pins, top ends…). So in the end it will give me an expensive solution based on used parts.
But this is not only a matter of cost, I don’t like the way the R100 runs, and I have tried quite a few.
Siebenrock might claim smoother running then the R100, IMHO it also runs smoother then the R80.


It is a good point that the Siebenrock-kit is not genuine BMW-parts, and therefore harder to get outside Europe. If I come in a situation where I need new pistons, rings or cylinders I have to get them shipped. But is there a chance to find these parts in Africa or Asia if I go for the BMW-solution (standard R80 or R100)? I don’t think so; they have to be shipped anyway… Even in here in Norway BMW have to order parts like this from Germany.
Of course if the Siebenrock is more prone to failure that’s a very good argument to use standard BMW-parts.

When it comes to using HPN I don’t think that’s the right solution for me. They make wonderful engines and bikes but the last years I have tried to get in contact with them several times (mail and phone) without luck. That’s not the kind of people I will depend on. There are also other issues like cost (which I’m sure reflects quality) and it looks like their development have stopped or at least slowed down.
Reply With Quote
  #8  
Old 26 Jan 2005
Mr. Ron's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Oct 2003
Location: Vancouver, BC, for now...
Posts: 792
Hello.
Interesting thread, thought i might add my 2 cents. I dual-plugged my R100 heads along with polished and flow-tested the ports last year.The result, imho, is 100 percent better. Better fuel economy, smoother running, faster punch! As far as the exposed spark-plug goes, even if you break it, you still have i left to run on until you can make repairs. I also burn reg. gas exclusively.
The compression problem... i read somewhere that you can shim the cylinders to reduce compression in problem fuel areas. Simply done in a few hours max. I've never tried this though, any comments?


Good luck!
Reply With Quote
  #9  
Old 26 Jan 2005
Gold Member
Veteran HUBBer
 
Join Date: Mar 2001
Location: British Columbia
Posts: 246
Lowering the compression through shims is possible, and your right is shouldn't be that difficult. However, you would loss at least some of the advantages of the Siebenrock kit in doing this. Part of how they increase the power with the stock valves/ carbs is by raising the compression.

Back to the previous comment on Ted Simon's bike. I recall the 1000cc modification being done by a shop in Britain (I'm sure the info is on his web site). The R100GS was sold in the US with the smaller valves (and carbs, if I am correct - Grant?) this may have been what they did, just swap the parts over.
Reply With Quote
  #10  
Old 26 Jan 2005
Mr. Ron's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Oct 2003
Location: Vancouver, BC, for now...
Posts: 792
Hello.
The US model R100GS (mine ) came equiped with 32mm carbs, although i don't know if the valves are also smaller or the same as the 40mm Canadian and European models.
Reply With Quote
  #11  
Old 26 Jan 2005
Grant Johnson's Avatar
HU Founder
Veteran HUBBer
 
Join Date: Dec 1997
Location: BC Canada
Posts: 7,216
The US R100's (later series, e.g. GS) all came with 32mm carbs. Everyone else that I know of got the 40mm carbs and bigger ports. I don't know if there was a valve difference or not.

But we can find out - give me the engine and frame number of both a US bike and a Canadian and / or European, and we can look up the part numbers and see if there is a difference.

Post em here!

The easiest R80 to R100 is just add the COMPLETE topend of an R100, pistons out.

Note that it is a bad idea to use R80 heads, even though they'll fit, with R100 pistons/cylinders - you will probably LOSE power. A few people have reported success, but the consensus seems to be that it's not good.

A used R100 topend is reasonably priced generally, and if it's a US topend, then you can use the original R80 carbs easily. DO change the jetting of course!

You can also use the R80 32 mm carbs with the Euro topend, but jetting will have to be sorted the hard way. Start with the R100 settings and check it carefully.

That's all I can think of at the moment!


------------------
Grant Johnson

Seek, and ye shall find.

------------------------

One world, Two wheels.
www.HorizonsUnlimited.com
__________________
Grant Johnson
Seek, and ye shall find.

------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
Reply With Quote
  #12  
Old 26 Jan 2005
Mr. Ron's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Oct 2003
Location: Vancouver, BC, for now...
Posts: 792
Hello Grant. Here's some #'s:
Frame:wb1047805k6153181
Engine:kbm0980425a
This is an '89R100GS/PD US model.
Reply With Quote
  #13  
Old 26 Jan 2005
AliBaba's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Apr 2001
Location: Norway
Posts: 1,379
Thanks for an interesting discussion!

Okay I see that most of you would prefer to use genuine BMW-parts.
The compression might be a problem with low octane petrol (but no one has tried it). It’s easy to come around the problem when/if it happens by reducing the compression temporarily or use octane booster. (I’m not sure if it will be a problem because other bikes run much higher compression without problems)

I can’t see why it would be easier to use a complete R100 top end, for me the job looks the same and it will cost more money. If I even have to use an US topend (or change carbs), this doesn’t look like an easier way to me. The Siebenrock-kit also runs much smoother and has more power then the R100. So for me it looks like:

Siebenrock:
+Cheap
+Runs smoother then R100 (and R80), esp on low RPM
-High compression might be a problem with low octane petrol (fixable)

R100
+Genuine BMW-parts
-Expensive
-Based on used parts
Reply With Quote
  #14  
Old 26 Jan 2005
Gold Member
Veteran HUBBer
 
Join Date: Mar 2001
Location: British Columbia
Posts: 246
AliBaba,

I agree with your assessment of the advantages of the Siebenrock kit over stock parts. However, I personally don't see an easy way to fix the compression/ fuel problem for traveling. Lowering the compression involves pulling the top end (replacing all gaskets/ o-rings = $), shimming, and rejetting the carbs. hardly something I would want to do more then once. If you do this, you will then lose much of the power advantage you gained going to 1000cc.
I don't think there is any question that the Siebenrock kit is not a great mod....for a bike that can be assured a steady diet of 94 octane fuel. Perhaps carrying octane booster would do the trick?
However, like you say, if the Siebenrock does indeed run smoother, perhaps it is worth the hassle in the long run.
On another note, it was once suggested to me that if I wanted to up the power of my R80, I should install the high compression pistons from the European road models (9.5 to 1 I think) and dual plug/ polish the heads. This should deliver at least a 10% boost in HP and torque, and will run on 87 octane as the bore is still narrow, and the dual plugging reduces detonation. So this Modification would:
*Increase power,
*keep the smooth running nature of the R80
*increase fuel economy
*stay with stock parts
*known setup = easy to rejet carbs.
*be economical
Worth condidering; price wise, I suspect it would end up similar to the Siebenrock kit if you could get some used parts (cylinders/ pistons).
Great discussion BTW,
Reply With Quote
  #15  
Old 28 Jan 2005
Vaufi's Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Jan 2004
Location: Munich, the beer capital
Posts: 1,047
Quite interesting point re carbs. I suppose most people tend to use the bigger carb when changin to 1000 cc.
The 32 mm carbs fitted on the 1000 cc engine will offer you a better and smoother performance in lower revvs due to better flow, but naturally the performance will be lower than in higher revvs with the 40 mm carb.
Another + for the 32mm carb is a lower fuel consumption, which is an important issue when travelling in areas with few petrol stations.
__________________
Only when we pause to wonder
do we go beyond the limits of our little lives.
(Rod McKuen)
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 16:56.