Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > Yamaha Tech
Yamaha Tech Originally the Yamaha XT600 Tech Forum, due to demand it now includes all Yamaha's technical / mechanical / repair / preparation questions.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 21 Jun 2011
Registered Users
HUBB regular
 
Join Date: Feb 2011
Posts: 70
Problems with bleeding front brake

Overhauled the caliper and changed the piston in the handle/main cylinder, i have altso bought new brakelines from hel.

I tryed to bleed the brakes for over an hour today, but the oil wouldnt go in. only a small amount. filled up the revisor, pumped the brake many times. opened the bleed valve and did the same over again.

noe i have taped the handle to the bar for the night. maby some oil finds its way down the brakeline during the night.

any pointers on what to do

1991 xt600
Reply With Quote
  #2  
Old 21 Jun 2011
Registered Users
Veteran HUBBer
 
Join Date: Jan 2001
Location: Cork,Ireland
Posts: 150
The pistons might have been pushed back in so far that there isn't any room for fluid to get in, you might be able to use compressed air to blow the pistons out a bit and fill the caliper through the bleed nipple hole.
OR you could try back bleeding with another bike and a hose connecting the bleed nipples pump the other bikes brake and open the bleed nipples and siphon the fluid out of your bikes master cylinder.
This can work well to remove bubbles as they are being forced up not down.
Reply With Quote
  #3  
Old 22 Jun 2011
Registered Users
Veteran HUBBer
 
Join Date: Mar 2011
Location: London
Posts: 105
Overhauled the caliper and changed the piston in the handle/main cylinder, i have altso bought new brakelines from hel.


I tryed to bleed the brakes for over an hour today, but the oil wouldnt go in. only a small amount. filled up the revisor, pumped the brake many times. opened the bleed valve and did the same over again.

Hiya, well done on the replacement of the valve, if it's in correct, overnight no oil should pass into the brake line or the calliper. Your discription of bleeding the brakes of air appears to be not quite right. Are you opening (just a little to allow oil to pass) the bleed valve as you depress the brake lever, then, closing the bleed valve before releasing the brake lever? To do it this way one should push the air out through the bleed valve untill oil is comming out without any air bubbles in the oil.

noe i have taped the handle to the bar for the night. maby some oil finds its way down the brakeline during the night.

Sometimes leaving overnight is not such a bad idea, as, if there should be any remaining air in the brake line this might* rise overnight to the top and the brake piston. To see if this has happened, hold the lever in, and you might see bubbles of air riseing into the brake resevoir. Having said this, I should add the first operation ought to have done the job of removing all the air in the first place.
* might ! but not likely!

any pointers on what to do

This job is best done with two people.

Have you a bleed valve and line attached to the bleed valve (nipple) or a bleed line that is in oil at the other end?

Hope my comments are of help and makes sense, as its late!

Good luck

Socks
Reply With Quote
  #4  
Old 22 Jun 2011
Registered Users
HUBB regular
 
Join Date: Jun 2011
Posts: 29
Bleeding brakes

Hi,

also, please be aware that depending on the type of reservoir, low pressure can develop in the reservoir, causing difficulty.
If there is a flexible rubber seal under the lid, leave it off during the bleeding process. I had this problem on a 1998 Suzuki VS 1400. Stuck in New Delhi, it took a sleepless night to figure out what was happening.

Regards,
Mark.
Reply With Quote
  #5  
Old 22 Jun 2011
Registered Users
HUBB regular
 
Join Date: Feb 2011
Posts: 70
thanks for the pointers. as i walked by the bike this morning i couldnt see a increase of fluid in the revisor.

earlier i have pumped the brakes repeatedly, then held it in while opening the valve on the caliper. if i understand you right i should have the valve open as i press the brakes and close it when its all pressed in?


i didnt know that i could press the pistons too long into the caliper. i guess that i see 1 mm of the piston... but whit the small amounts of brakefluids that i managed to press down the line yesterday i dont think the fluids have reatched the caliper yet.
Reply With Quote
  #6  
Old 22 Jun 2011
Registered Users
Veteran HUBBer
 
Join Date: Jan 2001
Location: Cork,Ireland
Posts: 150
I rebuilt my caliper and master cylinder on my Dominator recently and installed new Hel braided lines at the same time.
When I went to bleed the caliper the little air trapped in the front caliper stopped the bleeding process, If you want to try filling the caliper you may need to open the bleed screw and fill the reservoir with fluid to see of gravity will take it down.
If the caliper doesn't fill then it could be airlocked, this is where you need to put a piece of wood in the caliper to stop the pistons shooting across the shed and blow the pistons out with the compressed air gun into the bleed nipple port(remove the nipple)
They should come out and you can fill the caliper carefully through that hole.

To bleed the brakes you should remove the reservoir cover.
fill to the indicated level and start pumping with the bleed nipple closed and your ring spanner over the bleed nipple.
You also need a short length of hose from the bleed nipple into a jar or other container with a little brake fluid in the bottom.
This stops the hose sucking air back in as the fluid comes out.

Pump the lever until you feel some resistance, then holding the lever in open the bleed nipple until fluid and bubbles come out the hose.
Keep the lever pulled in, and tighten the nipple again.
Pump and repeat until there are no more bubbles and the lever feels hard.
If you can't get a hard lever, you may have trapped air bubbles, this is where you leave the lever pulled in overnight.
Try and ensure the reservoir is the highest point so the bubbles will rise to it, not some loop in the brake hose.
Reply With Quote
  #7  
Old 22 Jun 2011
*Touring Ted*'s Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2005
Location: Wirral, England.
Posts: 5,654
You could also try reverse bleeding or do what I did years ago and bought a MITYVAC for about £35.

Good bye brake problems...
__________________
Did some trips.
Rode some bikes.
Fix them for a living.
Can't say anymore.
Reply With Quote
  #8  
Old 22 Jun 2011
Registered Users
New on the HUBB
 
Join Date: Jan 2011
Location: Bristol, UK
Posts: 10
Brake bleeding

Some things to check.
Remove the bleed nipple on the caliper and check that the hole is clear (in the nipple).
In the master cylinder, did you fit the piston seal the correct way round?

Also if you are 'pumping' the lever with the diaphram off, cover any paint or plastics !
When I have had similar problems in the workshop, I sometimes use a large syringe to 'draw' the brake fluid through.

Eddie.
Reply With Quote
  #9  
Old 22 Jun 2011
Registered Users
Veteran HUBBer
 
Join Date: Jan 2008
Location: Inverness, Scotland
Posts: 249
Just done my Laverda which has a slightly problematic line layout (a splitter on the yoke). Couldn't get the new stainless lines to fill until I tried this: I got a small plastic bottle with a nozzle on (a small washing up bottle or similar) and squashed it down before connecting it to the bleed nipple with some silicone hose. I then opened the nipple and pumped the lever slowly- the bottle trying to regain its original shape caused a vacuum which really helped move the fluid. Cheap and simples!
__________________
Our FB page: https://en-gb.facebook.com/Africa2Up/
Reply With Quote
  #10  
Old 22 Jun 2011
Gipper's Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Mar 2004
Location: Saltspring Island,Canada/Poole,UK
Posts: 1,081
if you use compressed air as mentioned put some wood or similar on pistons and be VERY gentle - it only needs a slight 'puff' of air to move them.

you can also just suck on the bleed hose coming off the bleed nipple initially to create an underpressure as you are pumping the brake lever - this works to pull the fluid through, then insert it into a container of fluid and bleed as normal.

but the only drawback is as you suck on the hose you get water vapour bulidup in the low pressure hose which may or may not go through the bleed nipple and into the caliper,even if it did, im pretty sure it would get washed out by the fluid anyway - so any fluid coming out shouldnt be reused.

It can still take a while to get fluid through so persevere
__________________
Cheers
Grif

'11 KTM 450 EXC
'09 Suzuki DR650
'00 Discovery Series 2 V8
'95 Defender 90 300 Tdi Overlander
http://gipperstravels.blogspot.ca
Reply With Quote
  #11  
Old 22 Jun 2011
bacardi23's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Sep 2007
Location: XXX<-Portugal->Azores->Santa Maria (island)
Posts: 1,544
After you're able to get it working, make sure your front disc brake rotor is true!

My front one is bent.. don't ask me how because I got no idea....and when it rotates, it pushes the pistons one way and when you go press the brake it just won't grab the disc as the pistons are to far away...


Vando
Reply With Quote
  #12  
Old 22 Jun 2011
Registered Users
HUBB regular
 
Join Date: Jan 2010
Location: Bridgend, UK
Posts: 33
You need a vacuum. I used a large syringe and a suitable bit of rubber hose to draw fluid from the bleed nipple. All done in about 30 seconds after having the exact same problem after fitting Hel hoses too. Once bled properly and the new pads were bedded in the braking was much more positive.

Regards - Alastair.
Reply With Quote
  #13  
Old 23 Jun 2011
Registered Users
HUBB regular
 
Join Date: Feb 2011
Posts: 70
it was the pistons on the caliper that was too far in. i need to get a place with compressed air to fix it.

i altso found out that one of the gaskets on my fork is blown. it was dripping oil down on the caliper i just changed the fork oil...

where is the easiest place to buy new ones? is it a easy job?
Reply With Quote
  #14  
Old 23 Jun 2011
bacardi23's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Sep 2007
Location: XXX<-Portugal->Azores->Santa Maria (island)
Posts: 1,544
well, If you just changed the fork oil you might be able to drain it back to a clean container of some sort...

I never replaced the seals on my XT forks but have fully dissassembled the YZ forks that I have on my XT and can tell you that it's quite an easy job if you have the right tools..

For a matter of fact, the XT fork seals should be much easier than the inverted forks of the YZ since the XT ones you can take them from the top of the fork whilst on the YZ you have to fully separate the upper and lower forks...


These guys on here should be able to tell you how to do it properly!

Good luck!
Vando
Reply With Quote
  #15  
Old 23 Jun 2011
Registered Users
Veteran HUBBer
 
Join Date: Dec 2008
Location: Denmark
Posts: 1,417
I made a guide to disasseble the forks to swap oil/springs after doing it on my xt600e. You just need to take it a bit fuher apart.....Read on

Its not that hard, but a bit time consuming the first time, and tricky without proper tools.

You need to take the fork legs apart as i recall, and you need either an airtool or buy/make a special tool.

This is a guide for replacing the springs, you just need to do the same, and then also remove the unbracobolt in the bottom on the fork (loosen it with airtool before you take the forks apart. Or take them apart and weld a size 32 nut (again, as i recall) to a rod, and put it down the frokleg ho hold "against" the unbraco.



-Put the bike on a stand.
-Remove the speedocable fromt he front wheel.
-Remome the brake by unscrewing to bolts. Twist the caliber back and forward, and remove it by sliding it backwards.
-Loosen the 4 nuts on the lover part of the right leg. After that you can take out youre front axle, do that.

-Loosen the tops of the legs, just loosen them 1/4 of a turn so they will be easier to get of in a few steps, youll probably need to remove you're handlebars. Its 4 bolts, and is real easy.
-Loosen the upper mounts for both the legs, 2 bolts and 2 nuts on each side.
-Now do the same for the lower ones.
-Slide the legs down, they are now off the bike.
- Take the top covers of, remmeber you loosend them before, now theyre easy. If you can, put some weight on them to save the threads a bit.

-When you get them of, you will se the spacer, then a washer, and then the spring. Remove that, and set the leg upside down in a bucket. Pump the leg up and down to get all the oil out, and let it drip of.

Heres where you ned to disasseble more, like mentioned at first

-You're now halfway done, i usualle poor one cup of oil down the legs again, oump the leg up and down a bit, and then turn it upside down, and pump it again,. and let i drip of. Thats just to get all the dirt out.

-Now, compress the leg, and poor oil in it to 16-14cm from the top, depending on how hard you want it. You need 550ish ml to do that.
Just use some 10W fork oil for the job.
-Now its all backwards, remeber to put the new springs in correctly. The end which is tightest together should face up.
It kinda sounds like much, but it isnt. You're jsut remomving the front wheel, taking the legs of, and take the springs out, and change the oil.


Hope you can use it.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
KLE front brake upgrade anyone? rohirim Kawasaki Tech 9 30 May 2013 10:54
bleeding front brakes xt600fun Yamaha Tech 12 28 May 2010 08:11
Rear brake bleeding problem, ? bradley j Yamaha Tech 21 25 May 2009 23:39
Front brake problem Mark Yamaha Tech 3 19 May 2009 23:17
XT front brake pads jbw Yamaha Tech 3 13 Mar 2003 05:22

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 12:02.