Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > Yamaha Tech
Yamaha Tech Originally the Yamaha XT600 Tech Forum, due to demand it now includes all Yamaha's technical / mechanical / repair / preparation questions.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 17 May 2007
Registered Users
New on the HUBB
 
Join Date: May 2007
Location: melbourne
Posts: 17
xt600 weird starting problem

After getting my needle and set fixed my problem now is the motor will not start when its cold i have to use aero start to fire it up. Once its warmed up then i can stop it and restart it with out probems. Whats the deal? Choke seems to be fine(no sticking)

It also has a hickup (backfire)while its running once every few secs.
Can any body help out?

niko.:confused1:
Reply With Quote
  #2  
Old 17 May 2007
Registered Users
Veteran HUBBer
 
Join Date: Mar 2007
Location: UK
Posts: 4,343
Read on

Hi Niko,
You are where I was about 2 months ago; new bike (to me) and an issue with poor starting and a newbie on the HUBB.
I am no expert on the engine and I don't want to try to diagnose your problem but I do advise you to read the back-threads in this technical forum for some great advice from others who do know what they are talking about! It sorted me out. It is a simple design and one of the guys out there on this forum has seen it before. Look at the threads for both the XT and the TT (my bike) - the engines are much the same.

For quite some time I thought my bike had a fuelling problem but it turned out to be electrical (the earth and, maybe, a dirty spark plug).

Thing is to change one thing at a time and look for the effect that has, be methodical and patient also; if you have a spark and good fuel then it will fire up and then you can adjust/fine tune.

Hope this helps,

Dave
__________________
Dave
Reply With Quote
  #3  
Old 17 May 2007
Registered Users
Veteran HUBBer
 
Join Date: Jan 2001
Location: Stockholm
Posts: 651
Idle mix

If before the replacement of the needles etc (why did you do that anyway, never seen an XT where that was necessary), the engine ran, and you did not change anything else, I'd guess the idle mix is now too lean, as you have installed new, not worn jets.
The easy fix is to adjust the idle mix, see earlier posts.

Always a good idea to have a good, new spark plug BTW.

If the above doesn't work, start worrying about the following:
Further, to install new jest you have taken the float bowl off. You sure you did not bent the float or something?
Is enough fuel arriving in the float bowl?
Are the connections between carb and cilinder head airtight?

Auke
__________________
Auke
http://aukemarieke.blogspot.com
Reply With Quote
  #4  
Old 17 May 2007
Registered Users
New on the HUBB
 
Join Date: May 2007
Location: melbourne
Posts: 17
thanks guys for replying, first off its got a new battery(drycell) a new spark plug, and new needle and seat( old one was worn out and had stuck)
the float is ok and not bent and the rubber manifolds are good.

Now it could be an earth problem(will test that out tomorrow)
One thing it does do once its running is if i put my hand over the air cleaner hole the motor starts to really rev this normal??

Or maybe the spark plug gap is not right or idle screw not adjusted right(its 2 turns out now)

niko.
Reply With Quote
  #5  
Old 17 May 2007
Registered Users
Veteran HUBBer
 
Join Date: Mar 2007
Location: UK
Posts: 4,343
Idle screw

Niko,
My idle screw is set at near enough 3 turns out from fully in; there are two different values in the cd information that I have and this is the average of those recommendations; all of this for the 3AJ engine in a TT600R. Set at 2 turns it would be running lean I guess, but I don't know how sensitive the idle screw is to one whole turn!!

Cheers,

Dave
__________________
Dave
Reply With Quote
  #6  
Old 17 May 2007
Moderated Users
Veteran HUBBer
 
Join Date: Oct 2005
Location: Umtentweni, Kwa Zulu Natal, South Africa
Posts: 182
Choke

Hi,

in the swimmer chamber is a channel where the pipe for the choke fits in. I check that channel with some water drops and look if they make it through the channel into the chamer. If the channel is blocked, this is often the problem if the XTs don`t like to start when it is cold. This happens often after bikes did park for a long time with fuel in the carb.

regards Thomas

www.motozulu.com
Reply With Quote
  #7  
Old 17 May 2007
Registered Users
New on the HUBB
 
Join Date: May 2007
Location: melbourne
Posts: 17
again thanks guys , i'll try the idle screw at 3 turns and see how that goes.
One thing ive noticed with the spark plug its blackish not gray once i remove it this means its running rich?

Also motor has bee sitting awhile with out been started so water could be an issue.
niko.
Reply With Quote
  #8  
Old 17 May 2007
Registered Users
Veteran HUBBer
 
Join Date: Mar 2007
Location: UK
Posts: 4,343
Niko,

I would not want to send you down a dead-end road! Everything so far sounds like a fuel problem (but it could be electrical!!)

As aukeboss says, have a look back (do a search in here) at the past threads about setting the idle screw; there is loads of good information for the XT and TT (so look for both) with lengthy descriptions of what to do.

Good luck. If you are systematic and change one thing at a time and look for what happens it will get sorted out,

Cheers,

Dave
__________________
Dave
Reply With Quote
  #9  
Old 18 May 2007
Registered Users
New on the HUBB
 
Join Date: May 2007
Location: melbourne
Posts: 17
well today i tried to start it again with the same problem. I had a look at the spark and it was there and didnt look to strong(not blue)
I went over the earth conections and made sure they were clean.
Once it started it again with aerostart and once warmed it ran(still backfiring) Took it for a drive and had a few misses when i gave it a boot full.
Next thing im going to get rid of the old fuel(98oct) and put some new 95 in.
See how that goes.

niko.
Reply With Quote
  #10  
Old 18 May 2007
Registered Users
Veteran HUBBer
 
Join Date: Mar 2007
Location: UK
Posts: 4,343
Plugs and things

Again, as mentioned before, it's worth fitting a new spark plug - I am getting a spark with my old one but I don't know how old it is so I have a brand new one ready to fit the next time I have the tank off (and that won't be long!!).
It's an Irridium type which are supposed to be better at starting as well as running and they don't cost too much here in UK.

My earth problem was sorted by cleaning the back of the coil where it touchs the frame - it was dirty/greasy - once that was sandpapered the bike was much easier to start!!

Cheers,

Dave
__________________
Dave
Reply With Quote
  #11  
Old 18 May 2007
Registered Users
New on the HUBB
 
Join Date: May 2007
Location: melbourne
Posts: 17
sparkplug is a new one, and i did the same sanding the area under the coil mounting.

One thing Dave, what gap did you use on the plug?

niko.
Reply With Quote
  #12  
Old 18 May 2007
Registered Users
Veteran HUBBer
 
Join Date: Mar 2007
Location: UK
Posts: 4,343
0.8 mm

Hi again Niko,
The recommendation is 0.8 - 0.9 mm. I used 0.8mm on the NGK DPR98EA plug.

I was not sure if cleaning the plug made any difference as well as "re-earthing" the coil - I did both at the same time, hence my comment about changing one thing at a time and checking for the result.

Cheers

Dave
__________________
Dave
Reply With Quote
  #13  
Old 20 May 2007
Registered Users
New on the HUBB
 
Join Date: May 2007
Location: melbourne
Posts: 17
thanks Dave, ive set that gap right, set the idle screw to 2.5 (3 no good)turns and took it for a test drive and well its till not happy. Its fine running around in 1st and 2nd but as soon as you floor it it bogs down bad.
Must try again.

niko.
Reply With Quote
  #14  
Old 20 May 2007
Registered Users
Veteran HUBBer
 
Join Date: Jan 2001
Location: Stockholm
Posts: 651
`One thing it does do once its running is if i put my hand over the air cleaner hole the motor starts to really rev this normal??`

No, not normal. It means two things: 1) the idle mix is way, way too lean and 2) the idle speed setting is way, way too high.
If you block part of the air intake, apparently the mix gets better ...., ie richer.

When you said you replaced needle and seat, did you mean the float needle and seat or the needle and jets in the carb throat(s)?

Just presuming you mean the float needle, I'd go back to the float level setting, check that one by either removing the float bowl and measure or by using the way described in the manual with a piece of transparent hose.
Or the check the other possibilities for the lean mixture: false air drawn in somewhere, blocked jets etc.

Auke
__________________
Auke
http://aukemarieke.blogspot.com
Reply With Quote
  #15  
Old 20 May 2007
Registered Users
New on the HUBB
 
Join Date: May 2007
Location: melbourne
Posts: 17
thanks for that,i'll have another look tomorrow does sound like theres must be another air leak somwhere. Yes you were right i did replace the float needle/seat. I did use the air compressor to clean the inner workings of the carbie so im sure the jets are fine.
Could be the manifold rubber inlets leaking.
So to richen up the mixture the idle screw needs to wind out more to 3.5 will try that tomorrow too.

thanks,
niko
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
1990 xt600 starter problem jimmy mc Yamaha Tech 1 17 Sep 2007 21:45
XR600 Starting Procedure?? VintageHondaKid Honda Tech 15 27 Dec 2006 15:58
1150GS starting problem? Steve Pickford BMW Tech 4 19 Feb 2006 02:57
3AJ Starting Problem bolla Yamaha Tech 1 1 Apr 2003 16:46
Starting Problems xt600 arne Yamaha Tech 2 3 Jan 2001 18:30

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 23:32.