Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > Yamaha Tech
Yamaha Tech Originally the Yamaha XT600 Tech Forum, due to demand it now includes all Yamaha's technical / mechanical / repair / preparation questions.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 17 Feb 2007
Registered Users
New on the HUBB
 
Join Date: Nov 2006
Location: Syd
Posts: 12
should i let it go?

hi all,
I have had an 83 xt600 for around a year and love it. all sorts of fun in deserts in W.A aus, then had it trucked to NSW where I now live. I rode to Melbourne (1000km) and it seized. I have taken it apart and found the piston to be, well, a bit melted. as far as I can tell the cylinder can be rebored, piston replaced, bearings replaced etc. is a rebuild worth it? I changed the oil and filter before i left ( ignoring obvious 'must maintain bike better or at least keep fluids topped up' maintainance) The bike hasn't been treated badly (aside from me). the bike is in bits now and i have access to tools I need to do it. I am wondering though, is it worth the time and expense to rebuild the engine? I am intending to have the thing around for a while and hopefully do quite a few kms. I know anything can be fixed but given the age and purpose of these bikes, should I be thinking about something a little, well, less stressed. I would appreciate any input. thanks.
Reply With Quote
  #2  
Old 17 Feb 2007
Registered Users
HUBB regular
 
Join Date: May 2006
Location: scotland
Posts: 34
If you like the bike why not? You know it, and it's seen you OK. An option could be a replacement engine. Don't know what its like for imports/breakers where you are, but a newer engine from a low mileage import could be an option.
They are good grin factor bike.
Neil
Reply With Quote
  #3  
Old 17 Feb 2007
Registered Users
New on the HUBB
 
Join Date: Nov 2006
Location: Syd
Posts: 12
they certainly are! Im just wondering, given its age what should I be expecting to go wrong/ break. whats the lifespan of these bikes? it says its done 44000km and Im not sure I believe that. In terms of metal degredation etc.
Reply With Quote
  #4  
Old 17 Feb 2007
Registered Users
HUBB regular
 
Join Date: May 2006
Location: scotland
Posts: 34
Search back through the posts using search option, there's some horror stories and also some high milers, a few 100k+ bikes. Is the rest of her in fair enough shape?
Reply With Quote
  #5  
Old 3 Mar 2007
tomwest's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Sep 2006
Location: At the moment:Zanzibar
Posts: 116
save her.

Hi, Im about to put a replacement engine in my 86 tenere´ The old 1vj engine has 120.000km on it now and I probably would have restored it if I hadn´t found a 3tb for a reasonable price.If the bike otherwise is in a fair enough condition why not fix it. Sure you can buy a newer,but they brake too
__________________
Places to be and things to do, see you all out there!!

Cheers.

Tom.
Reply With Quote
  #6  
Old 6 Mar 2007
*Touring Ted*'s Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2005
Location: Wirral, England.
Posts: 5,654
Think how much it will cost to fix weighed against how much a similar bike is to buy ??

Personally if its a rat bike, sell it in pieces on ebay, save a little and get something which isnt going to fall apart when you hit a rock
__________________
Did some trips.
Rode some bikes.
Fix them for a living.
Can't say anymore.
Reply With Quote
  #7  
Old 9 Mar 2007
Registered Users
New on the HUBB
 
Join Date: Nov 2006
Location: Syd
Posts: 12
rebuild

well... it is indeed a rat bike but I have decided, perhaps irrationally, to go for the rebuild. So far; new bearings, gaskets seals obviously, rebore, piston etc, recondition head, cam chain, oil pump, which was the cause of all this and not my ineptitude, valves etc. Once that is done ( I might even paint it (!)) I will do other fun things like chain sprockets, front wheel bearings air filter and any of many other things I find that need replacing.
I have to say that without crawling through this site I wouldnt know half the things I do now about the innards of these machines, and have come across most of the problems described within. like how the hell do I get the bearing off the crankshaft... freezer fridge get the shop to do it etc...
Many thanks for all this.
Reply With Quote
  #8  
Old 9 Mar 2007
mollydog's Avatar
R.I.P.
Veteran HUBBer
 
Join Date: Aug 2003
Location: california
Posts: 3,822
the experience and knowledge gained are well worth it.
__________________
Patrick passed Dec 2018. RIP Patrick!

Last edited by mollydog; 26 Mar 2009 at 04:33.
Reply With Quote
  #9  
Old 9 Mar 2007
Registered Users
New on the HUBB
 
Join Date: Nov 2006
Location: Syd
Posts: 12
thanks

i am hesistant to say too much before i hear it running but.... it has so far been an amazing experience. i think I know what everything does now and all those noises make sense. I spent a lot of nervous hours in the desert with this bike ( I found a lot of red dirt in the head) and I think I know what it means.. I'm waiting for a new piston and then the rebore, found the bearings and gaskets and I'm learning a lot. I think the expense is well worth it. I could have bought another bike for what I paid so far but.... I think I need to post some pics... thank you all..
Reply With Quote
  #10  
Old 9 Mar 2007
mollydog's Avatar
R.I.P.
Veteran HUBBer
 
Join Date: Aug 2003
Location: california
Posts: 3,822
measure everything to spec before reassembly and oil it well too.
__________________
Patrick passed Dec 2018. RIP Patrick!

Last edited by mollydog; 26 Mar 2009 at 04:33.
Reply With Quote
  #11  
Old 9 Mar 2007
Registered Users
New on the HUBB
 
Join Date: Nov 2006
Location: Syd
Posts: 12
thanks for that, I'll certainly do that. the previous owner didn't have an air filter at all. hence the red dust. to be fair though that stuff goes through anything... one thing though, I haven't decided on rebuilding the crankshaft. there is minor ( within tolerance ) lateral movement in the conrod. everything else seems ok. there is no major wear in the bearings either. I'm replacing them ( all eight ) because I'm there already and I don't want to do this again for a long while. And yeah, the best part of all this, if expensive, was finding a very broken oil pump.
Reply With Quote
  #12  
Old 24 Apr 2007
Registered Users
HUBB regular
 
Join Date: Apr 2007
Location: Sydney Australia
Posts: 28
how did it go

Chopper511 how did the rebuild go.
I'm currently doing my XT 600e `96 mod currently.
Talking about seizing , I seized my XT550 some years ago. I'd just rebuilt it and on a cold winters morning (12deg C) running 40 weight oil it seized. Bugger hey. That's what you get for running heavy iol in cold conditions.
Therefore the XT 550 got rebuilt again.. it then went to Frazer island and a few more good trips before it was sold.

Where did you source your parts. Here in ozz they are quite expensive relative to the US or UK.
Reply With Quote
  #13  
Old 24 Apr 2007
*Touring Ted*'s Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2005
Location: Wirral, England.
Posts: 5,654
Iv been in your shoes many times...

usually when you've just spent £300 on a topend rebuild, the gearbox and clutch go next...

You fix them and then the main bearings start going

You fix them and then the big end goes and the suspension starts giving out..


You end up building a brandnew bikes at 3x the cost of getting a good one.

If you enjoy the spanner time and want to learn then go for it.. be prepared for irritation and bills though.
__________________
Did some trips.
Rode some bikes.
Fix them for a living.
Can't say anymore.
Reply With Quote
  #14  
Old 25 Apr 2007
Registered Users
HUBB regular
 
Join Date: Apr 2007
Location: Sydney Australia
Posts: 28
Repair or scrap it

It's fair to say that my current XT 600e has done a lot of work.
The guy I bought it off had done a trip to Cape York (nothern tip of Australia) I don't believe he treated the bike well therefore when he arrived back in the big city it was necessary to undertake considerable repairs.
He showed me an long list of reciepts and spoke of reboring, head reconditioning, bearing and gear changes etc. None the less the bike looked nasty.
I didn't necessarily believe the previous owner had actually done all the work mentioned but as I bought the bike for a bargain price ($1750.00 in 2000 so 7 years ago, the bike was only 4 years old at the time)
Soon after buying the bike it developed a very nasty bottom end knock. This ended up being a very poorly fitted keyway on the counterbalance shaft. I filed the keyways on both shaft and gear, made a new oversize key and used a healthy volume of loctite and away I went.
7 years on and about 50000KM the bike developed another very nasty bang (not really a knock). I expected this was bigend as I couldn't confirm what was repaired or the workmanship involved. If the key incident was and guide the workmanship was poor.
So the bike was stripped.
To my surprise the head gasket was blown which would account for the bang.
The 2 piston compression rings were aligned which would acount for the exessive blowpast and lack of compression.
The previous owner had rebored it, 1mm over, it truely does appear he did perform much of the work he mentioned, unfortunatly the workmanship is the primary issue, eg. volumes of silicon rather than "O" rings and gaskets..

The bottom end is tidy, There are 2 concerns I have,
1. lateral movement in the bigend is out of tolerance..
2. The bike would occasionally jump from 1st gear to neutral or second to neutral.
The gearbox is pandoras box to me. I havn't split the case yet.
Is it worth delving into the gearbox or could there be someother more obvious issue causing the bike to jump out of gear. (Should I start a thread for this?)

Any advice would be much appreciated.
Reply With Quote
  #15  
Old 25 Apr 2007
*Touring Ted*'s Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2005
Location: Wirral, England.
Posts: 5,654
Quote:
Originally Posted by markzz View Post
It's fair to say that my current XT 600e has done a lot of work.
The guy I bought it off had done a trip to Cape York (nothern tip of Australia) I don't believe he treated the bike well therefore when he arrived back in the big city it was necessary to undertake considerable repairs.
He showed me an long list of reciepts and spoke of reboring, head reconditioning, bearing and gear changes etc. None the less the bike looked nasty.
I didn't necessarily believe the previous owner had actually done all the work mentioned but as I bought the bike for a bargain price ($1750.00 in 2000 so 7 years ago, the bike was only 4 years old at the time)
Soon after buying the bike it developed a very nasty bottom end knock. This ended up being a very poorly fitted keyway on the counterbalance shaft. I filed the keyways on both shaft and gear, made a new oversize key and used a healthy volume of loctite and away I went.
7 years on and about 50000KM the bike developed another very nasty bang (not really a knock). I expected this was bigend as I couldn't confirm what was repaired or the workmanship involved. If the key incident was and guide the workmanship was poor.
So the bike was stripped.
To my surprise the head gasket was blown which would account for the bang.
The 2 piston compression rings were aligned which would acount for the exessive blowpast and lack of compression.
The previous owner had rebored it, 1mm over, it truely does appear he did perform much of the work he mentioned, unfortunatly the workmanship is the primary issue, eg. volumes of silicon rather than "O" rings and gaskets..

The bottom end is tidy, There are 2 concerns I have,
1. lateral movement in the bigend is out of tolerance..
2. The bike would occasionally jump from 1st gear to neutral or second to neutral.
The gearbox is pandoras box to me. I havn't split the case yet.
Is it worth delving into the gearbox or could there be someother more obvious issue causing the bike to jump out of gear. (Should I start a thread for this?)

Any advice would be much appreciated.
New thread.. hmm, i suggest a new forum
__________________
Did some trips.
Rode some bikes.
Fix them for a living.
Can't say anymore.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 02:23.