Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > Yamaha Tech
Yamaha Tech Originally the Yamaha XT600 Tech Forum, due to demand it now includes all Yamaha's technical / mechanical / repair / preparation questions.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 22 Sep 2009
Registered Users
Veteran HUBBer
 
Join Date: Feb 2002
Posts: 212
Will 18 inch wheel be OK in place of 17 inch in XT600E?

Hi All,

Does anyone know of any potential problem with fitting the 18 inch wheel from my crashed 3AJ Tenere in a 1991 3TB XT600E, which has a 17 inch wheel as standard?

I am hoping to keep a road tyre on the original wheel and fit an off-road tyre on the old Tenere wheel and swap that in for some green laneing. Has anyone done this? Is it likely that the tyre will hit the mud guard on full suspension compression. How can I check for this without taking the spring out of the shock absorber?

I am also intending fitting the old Tenere front wheel, with off-road tyre to the front, as they are both 21 inch I assume there will be no problem with this.

Thanks

Mark
Reply With Quote
  #2  
Old 22 Sep 2009
Steve Pickford's Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2003
Location: Oxford, UK
Posts: 994
Fitting an 18" rear in place of a 17" will raise your gearing. You may want/need to compensate for this by fitting a smaller front sprocket or a larger rear sprocket, especially if riding off road. Onroad, you could see a slight improvement in fuel economy as a result.

It's possible to calculate by how much the larger wheel raises your gearing by comparing the circumferences of both wheels with the respective fully inflated tyres fitted and comparing one measurement against the other as a percentage. You then apply the percentage difference to your existing front & rear sprocket ratio to calculate the change needed to retain standard gearing.

To check clearance, remove your seat & place a ratchet strap around each side of the swingarm. Tighten the strap until the shock is fully compressed & check if the wheel's hitting anything.
__________________
My photos: www.possu.smugmug.com
Reply With Quote
  #3  
Old 22 Sep 2009
Registered Users
Veteran HUBBer
 
Join Date: Feb 2007
Posts: 289
18" wheel

Had a 18" on my XT600E for one year, no problem installing it, no clearance problem with shock fully compressed.

21" wheel is exactly the same between XTE and tenere', had it on my bike for one year too.

now have XTZ660 wheels, both alu rims, rear 17", front 21".


Here a pic with tenere' wheels BikePics - 1990 Yamaha XT 600
Reply With Quote
  #4  
Old 22 Sep 2009
bacardi23's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Sep 2007
Location: XXX<-Portugal->Azores->Santa Maria (island)
Posts: 1,544
off topic... cyberzar.. that link of bikepics you posted.. shouldn't the guy have reinforced the frame because exhaust can isn't bolted on to the stock exhaust can mounting points??

Vando :confused1:
Reply With Quote
  #5  
Old 22 Sep 2009
Registered Users
Veteran HUBBer
 
Join Date: Feb 2007
Posts: 289
I'm the guy and used this setup for two years with no problems (no offroad). Now installed an inox metal tube, sagomed to replace standard exaust.

Have no pictures, but it's a really easy job, just get a plastic tube, hot air and make the model, then bring it to a welder and let him make it (with no holes) then go home and cut\make holes.
Reply With Quote
  #6  
Old 22 Sep 2009
Registered Users
HUBB regular
 
Join Date: Nov 2002
Location: Nottingham U.K.
Posts: 96
I have a mate with an XT600,sorry don't know what model,he has an 18 inch rim spoked onto the original hub.He uses trials type tyres no problem.
Reply With Quote
  #7  
Old 25 Sep 2009
Registered Users
Veteran HUBBer
 
Join Date: Feb 2002
Posts: 212
Thanks

Thanks everyone for your thoughts.

It’s good to hear that this has been done before without complications, but I suppose that I should stop being lazy and use ratchet straps to compress the rear shock absorber, especially as it is an aftermarket one. I had justified in my own mind not doing this in case it put too much strain on the rear sub-frame, but it has been reinforced.

I hadn’t fully thought through the effect on gearing, but hope that going 2 or 3 teeth up on the rear sprocket would be enough. The whole point of the exercise is to be able to simply and quickly swap wheels to go from road to off-road use.

Thanks

Mark
Reply With Quote
  #8  
Old 28 Sep 2009
Registered Users
Veteran HUBBer
 
Join Date: Feb 2007
Posts: 289
don't know if the straps system will work, but I'm not sure if you could damage your spring doing this... and compressed springs can be dangerous in any case.

Simply remove the shock, take the spring out, put the shock on the bike without spring. Put the 18" wheel on the bike, and test if all is OK, then assemble again the shock with the spring.
Reply With Quote
  #9  
Old 29 Sep 2009
Steve Pickford's Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2003
Location: Oxford, UK
Posts: 994
I'm not familiar with Yamaha shocks but know from experience that a lot of OEM items are not that easy to take apart. Generally, it's the more expensive WP/Ohlins/Wilburs etc that have the threaded bodies that allow easily removal of the spring. You may still require a shock spring compressor?

If your subframe is weak enough to be damaged by compressing the shock via ratchet straps, then it's got no right being on the bike in the first place? I've done this to my 400EXC & 950SE with no issues.
__________________
My photos: www.possu.smugmug.com
Reply With Quote
  #10  
Old 29 Sep 2009
Registered Users
Veteran HUBBer
 
Join Date: Feb 2007
Posts: 289
Sorry to disagree with you Steve, all our bike's shocks have a thread, some on the main body, others on the lower part, for spring preload adjustment.
Remove the spring from the yamaha shock is easy, without spring compressor. Some of them have a clip under the top ring, that can be removed once the preload is fully opened.
You could need just a ratchet strap to shorten the spring a little.

Compress the shock with the spring on means apply a LOT of strenght that IMHO could damage the frame if done not on the proper point... and maybe the spring also. Consider also that using the bike the force to compress the shock is distributed under the whole seatpost, using a strap is not the same thing.

Furthermore, one thing is compress the spring for one second, another is to compress it near its maximum for one minute or more.
Reply With Quote
  #11  
Old 29 Nov 2009
Registered Users
Veteran HUBBer
 
Join Date: Dec 2008
Location: Denmark
Posts: 1,417
Cool with the alloy xtz wheels.

Does the xtz use same hub as the xt from 90- ?

How about the spokes, does both the xt and the xtz ones fit?

I have a banged up rear rim on my 2003 xt600e, so info would be very helpful.

Thx.
Reply With Quote
  #12  
Old 20 Jan 2010
Registered Users
HUBB regular
 
Join Date: Jun 2008
Location: London,UK
Posts: 53
And vice versa, will a 17" fit on a XT600ZE? It will handle better, and you can compensate with gearing .... I find an 18" on the back just a bit of a handful...
Reply With Quote
  #13  
Old 21 Jan 2010
Registered Users
Veteran HUBBer
 
Join Date: Feb 2007
Posts: 289
hub and wheels are the same (back) front has a bigger brake disk. You can swap them, no problem.

babybadger: what is a XT600ZE? please give me your model:

43F
3TB
4PT
55W
3AJ
...

anyway xt600 rear wheels are often the same (ok the disk brake ones) excluding TT600 model (TTR\TTE TT etc)

Must confess that did not feel that big difference between 17 and 18 wheel, having used them both...
Reply With Quote
  #14  
Old 25 Feb 2010
Registered Users
Veteran HUBBer
 
Join Date: Oct 2009
Location: Derbyshire, England
Posts: 100
I had an 18" Morad ally rim spoked onto my original hubs using 9 gauge spokes and fitted with MT21 tyres. I found no problems even when fully loaded with luggage and bouncing through wadis.
The upgearing as a result was a bonus delivering higher MPGs.

Dan
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Changing from a 17 to 18 inch rim Xander Equipping the Bike - what's the best gear? 1 29 Nov 2008 16:05
17 thousandths of an inch? Pevrilito Yamaha Tech 11 3 Mar 2006 17:33
19 inch rims Gamble Yamaha Tech 0 15 Dec 2005 09:52
15 inch wheels hschout Equipping the Overland Vehicle 8 23 Jun 2004 16:37

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 14:11.