Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > Yamaha Tech
Rear brake bleeding problem, ? Rear brake bleeding problem, ?
Register FAQ Calendar Today's Posts
Yamaha Tech Originally the Yamaha XT600 Tech Forum, due to demand it now includes all Yamaha's technical / mechanical / repair / preparation questions.
Photo by George Guille, It's going to be a long 300km... Bolivian Amazon

I haven't been everywhere...
but it's on my list!


Photo by George Guille
It's going to be a long 300km...
Bolivian Amazon



Reply
Page 1 of 2 1 2
 
LinkBack Thread Tools Display Modes
  #1  
Old 11 May 2009
Registered Users
New on the HUBB
  
Join Date: Jun 2006
Location: Australia
Posts: 14
Rear brake bleeding problem, ?
Hi, I am bleeding the brakes on my XTZ660 and am having a problem with the rear brake, the front bled fine.
Firstly i should say the rear brake has been siting for a few months removed from the bike with caliper end hose disconnected. (I have been rebuilding the bike and had to disconnect the hose to remove it from the swingarm).

Ok so the problem is, i have it all back together and on the bike, I've re-filled the reservoir, hose it connected to the nipple on caliper.
I start pumping and cannot get any pressure build up, the pedal will press after press go straight to the bottom, and the fluid in the reservoir does not lower, whats the problem?

There are no leaks
There are no blockages in the hose from the reservoir to the master cylinder.
The rear brake was working fine before i took it off.

What do you think?

thanks
Brad
Reply With Quote
  #2  
Old 11 May 2009
Tenere Tom's Avatar
Registered Users
Veteran HUBBer
  
Join Date: Aug 2007
Location: Leeds UK
Posts: 449
If you get fed up I can get you all the bits to convert to drum at the back

You'll NEVER have to bleed it again!!!
__________________
Tom
I'm a country member...
Reply With Quote
  #3  
Old 11 May 2009
Registered Users
Veteran HUBBer
  
Join Date: May 2007
Location: yorkshire
Posts: 362
you could get in contact with Kev off the www.xt660.com web site.
Reply With Quote
  #4  
Old 11 May 2009
Contributing Member
Veteran HUBBer
  
Join Date: Mar 2003
Location: London,England
Posts: 358
On the reservoir check to see if it has a rubber dish, this has to be removed, seems obvious but I missed it as it looks like part of the reservoir and I was pouring fluid into the rubber.
I was doing the brakes on my TTR and could not figure out why the fluid was not going down.
Reply With Quote
  #5  
Old 11 May 2009
wolfzero's Avatar
Registered Users
Veteran HUBBer
  
Join Date: May 2009
Location: uk
Posts: 434
you need to bleed the master first at the banjo bolt on the master, then bleed the hose to the banjo on the caliper then you should be able to bleed it normally
__________________
XT 630 SUPERMOTO

GSXR750L KMX200

RF900 & GSX400X Impulse Projects
3.9 V8 Rangerover
Reply With Quote
  #6  
Old 11 May 2009
BlackDogZulu's Avatar
Registered Users
Veteran HUBBer
  
Join Date: Oct 2008
Location: West Wales, UK
Posts: 753
I've never had a problem bleeding the brakes on a bike, but if it was a car I would say that a seal has gone in the master cylinder. If it's been left dry for a while, perhaps the seals have perished.
__________________
2006 XT660R daily ride, 1994 XT600E about to be reborn, Blog: http://goingfastgettingnowhere.blogspot.com/
Reply With Quote
  #7  
Old 11 May 2009
Registered Users
Veteran HUBBer
  
Join Date: Jun 2008
Location: yorkshire england
Posts: 201
hi there ive had this problem in the past when the hose is disconected , the first thing to do is make sure the bleed nipple is not blocked ,it can happen . the main problem i think you have is there is no fluid in the hose to build up pressure what you can try is to get 2 hose clamps ,sqweeze 1 clamp as close to the outlet from the master cylinder , slave cylinder the other 1 a few inchs down the line, plyers and a rag will do if you have no clamps. pump the pedel if all go,s well you will get resistance on the pedel if so take the first clamp off and keep pumping, the fluid should now reach the second clamp , keep putting the clamps on until you are at the caliper and the hose is full ,then bleed as normal. oh by the way if you have goodridge this will not work ,if you have try unbolting the hose from the caliper put the hose in a jar of fluid and pump away this may bleed the hose enough ,then reconect . if you can borrow a syfone gadget that conects to the bleed nipple even better. just keep at it and you will get it to go. good luck zigzag
Reply With Quote
  #8  
Old 11 May 2009
wolfzero's Avatar
Registered Users
Veteran HUBBer
  
Join Date: May 2009
Location: uk
Posts: 434
zigzag if your still using rubber hoses and they are over 5yrs old bin them and fit braided lines
__________________
XT 630 SUPERMOTO

GSXR750L KMX200

RF900 & GSX400X Impulse Projects
3.9 V8 Rangerover
Reply With Quote
  #9  
Old 11 May 2009
djorob's Avatar
Seek and thou shalt find.
Veteran HUBBer
  
Join Date: Feb 2006
Location: Midlands/UK
Posts: 231
Bleenin!
Zigzags technique is a good trick and works well on standard rubber hoses. Steel braided can be damaged though.
Be carefull to pad out the jaws if using pliers (long nose pliers with insulstion tape padded jaws work well).
You could also try back filling the line from the slave cyl (caliper) bleed nipple.
There are specific pumps you can buy for this but a large syringe does it well.
Once the line is full is should bleed ok.
Dave.
Reply With Quote
  #10  
Old 12 May 2009
Bobmech's Avatar
Registered Users
Veteran HUBBer
  
Join Date: Sep 2008
Location: BOP , New Zealand
Posts: 183
I agree with Wolfzero's first reply, but first remove & check the bleed nipple isn't blocked.
When bleeding it you should pump the pedal quite fast to ensure the air bubbles don't remain at the highest point in the hose.
Bob
__________________
Remember that Assumption is the mother of all f**k-ups.
Reply With Quote
  #11  
Old 12 May 2009
Registered Users
Veteran HUBBer
  
Join Date: Apr 2003
Location: Manchester UK
Posts: 235
I had this problem as well.

Eventually I solved it by sucking the brake fluid from the resevoir into the cylinder by attaching a vacuum pump (the kind used to drain car sumps via the dipstick ) to the bleed nipple and going through almost an entire bottle of brake fluid. It seems that no matter how much I pumped the brake peddle there was always a trapped air bubble in the line causing a vapour lock.
Reply With Quote
  #12  
Old 12 May 2009
wolfzero's Avatar
Registered Users
Veteran HUBBer
  
Join Date: May 2009
Location: uk
Posts: 434
Quote:
Originally Posted by bruken View Post
I had this problem as well.

Eventually I solved it by sucking the brake fluid from the resevoir into the cylinder by attaching a vacuum pump (the kind used to drain car sumps via the dipstick ) to the bleed nipple and going through almost an entire bottle of brake fluid. It seems that no matter how much I pumped the brake peddle there was always a trapped air bubble in the line causing a vapour lock.
there is another way of getting the air out of the line its a bit slow but does work well
take the hose off the caliper and cable tie it to the resevoir or at the same height top the res up to the brim and use something to wedge the brake pedal down leave it over night and the air rises through the system and presto the line is full of fluid

__________________
XT 630 SUPERMOTO

GSXR750L KMX200

RF900 & GSX400X Impulse Projects
3.9 V8 Rangerover
Reply With Quote
  #13  
Old 12 May 2009
Registered Users
Veteran HUBBer
  
Join Date: Apr 2003
Location: Manchester UK
Posts: 235
Quote:
Originally Posted by wolfzero View Post
there is another way of getting the air out of the line its a bit slow but does work well
take the hose off the caliper and cable tie it to the resevoir or at the same height top the res up to the brim and use something to wedge the brake pedal down leave it over night and the air rises through the system and presto the line is full of fluid
That system works really well on the front brake even with everything attached and in situ. It's still a bugger on the back brake tho as when the air bubbles have gone you still got to get the hose back down to the rear brake calipers without getting any air in. Not so easy. Unlike the front brake lines, the back brake line has "elevation" changes both sides of the median that preclude the rise of air bubbles back into the resevoir.
Reply With Quote
  #14  
Old 12 May 2009
wolfzero's Avatar
Registered Users
Veteran HUBBer
  
Join Date: May 2009
Location: uk
Posts: 434
Quote:
Originally Posted by bruken View Post
That system works really well on the front brake even with everything attached and in situ. It's still a bugger on the back brake tho as when the air bubbles have gone you still got to get the hose back down to the rear brake calipers without getting any air in. Not so easy. Unlike the front brake lines, the back brake line has "elevation" changes both sides of the median that preclude the rise of air bubbles back into the resevoir.
maybe i should have added the following info to that post

once the line is full allow the brake pedal to return to its normal position and give it a couple of presses to fill the line fully and using some tape or a rubber bung block the eyelet of the banjo union to keep as much fluid in the line as posible whilst you route the line back to the caliper try and get as much fluid into the caliper as posible prior to ataching the line this wil help prevent air going back up the line if done carefully any air in the line will not be sufficiant to prevent the brake being bled as normal
__________________
XT 630 SUPERMOTO

GSXR750L KMX200

RF900 & GSX400X Impulse Projects
3.9 V8 Rangerover
Reply With Quote
  #15  
Old 12 May 2009
Registered Users
Veteran HUBBer
  
Join Date: Apr 2003
Location: Manchester UK
Posts: 235
I should have realised that. I'm having a stupid day. All the same. The back brake has always proved a nuisance for me what ever way you look at it. Traditional bleeding has always given me a PIA. Sucking the air and fluid through the system albeit with wastage has saved me an endless amount of faffing about. At £20 for the vacuum pump I now consider it an essential part of my mechanics toolbox.
Reply With Quote
Reply
Page 1 of 2 1 2

« Previous Thread | Next Thread »

Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
! URGENT ?: Rear brake pad spring friction to the rim base problem Samy BMW Tech 1 9 Apr 2009 19:30
Boxer Rear Brake Arm Andy Booth BMW Tech 3 25 Sep 2008 18:18
Rear Brake Caliper for KLR Riq Kawasaki Tech 6 7 Aug 2007 18:51
Rear Brake problems...help Uneasy Rider Suzuki Tech 2 11 Jun 2007 11:55
Rear disc brake Mark Yamaha Tech 4 28 Sep 2004 19:57

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

Your ad could be here, on EVERY page of the HUBB, or the whole website, or as many as you like!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.



All times are GMT +1. The time now is 03:26.

Contact Us - Horizons Unlimited Motorcycle Travellers Website - Archive - Privacy Statement - Top