Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > Yamaha Tech
Problems with bleeding front brake Problems with bleeding front brake
Register FAQ Calendar Search Today's Posts Mark Forums Read
Yamaha Tech Originally the Yamaha XT600 Tech Forum, due to demand it now includes all Yamaha's technical / mechanical / repair / preparation questions.
Photo by Ellen Delis, Lagunas Ojos del Campo, Antofalla, Catamarca

I haven't been everywhere...
but it's on my list!


Photo by Ellen Delis,
Lagunas Ojos del Campo,
Antofalla, Catamarca



Reply
Page 2 of 2 1 2
 
LinkBack Thread Tools Display Modes
  #16  
Old 23 Jun 2011
Registered Users
HUBB regular
  
Join Date: Feb 2011
Posts: 70
when im disassembeling the fork further ill need a T-bar the manual says. i dont have this? is there any suggestions on how tho make one ? how long has it to be?

Reply With Quote
  #17  
Old 23 Jun 2011
*Touring Ted*'s Avatar
Contributing Member
Veteran HUBBer
  
Join Date: Jul 2005
Location: Wirral, England.
Posts: 5,656
You can usually get away with using an airgun on the lower bolt...It spins off so fast, the rod can't spin quick enough with it and it shakes it lose.

The bar is to hold the damper rod still while you loosen the lower bolt. Without the tool, the whole thing spins inside the fork...


You can usually buy those tools for about £20.... I know you can for most other dirt bikes anyway. I ended up buying one for my DRZ because the bolt was beyond my little compressor.
__________________
Did some trips.
Rode some bikes.
Fix them for a living.
Can't say anymore.
Reply With Quote
  #18  
Old 23 Jun 2011
Registered Users
Veteran HUBBer
  
Join Date: Apr 2011
Location: Southampton, England
Posts: 110
Thanks to an old hand called Nid from Aldershot, there is a cheaper way.

Use a solid wooden broom handle. Shape one end with a tapered square. Like you would sharpen a pencil (same taper angle) but square. The smaller end of this taper should be about half the width you started with. (Don't go all the way to a point).

With the spring removed, locate the handle in the corresponding square hole in the fork. Then bash the handle (square shape forwards) in to the fork mercilessly. Once it is jammed in, grip the shaft with molegrips. You can then undo the bolt.

Leave the molegrips on the shaft - you will need to bash the side of them to release the handle back out of the fork.

Reassembly is the reverse...

It worked a treat on mine.
Reply With Quote
  #19  
Old 23 Jun 2011
bacardi23's Avatar
Registered Users
Veteran HUBBer
  
Join Date: Sep 2007
Location: XXX<-Portugal->Azores->Santa Maria (island)
Posts: 1,544
I made one for me.. it was a different shape but..

PVC pipe endings/joiners, a few screws and a iron saw blade to cut the grooves in to the shape of the nut..


Good luck with yours..
Reply With Quote
  #20  
Old 23 Jun 2011
Registered Users
HUBB regular
  
Join Date: Feb 2011
Posts: 70
does anyone have a picture of their own solutions and the sqrew inside the leg?
Reply With Quote
  #21  
Old 24 Jun 2011
Registered Users
Veteran HUBBer
  
Join Date: Mar 2011
Location: London
Posts: 105
Quote:
Originally Posted by bikereurope View Post
does anyone have a picture of their own solutions and the sqrew inside the leg?
Whats up fella, is it not working out for you?

Have you tried the above solutions/recommendations?

If you have the springs out now, with a good light behind you, you should be able to see the shape of the inverted section in the bottom of the fork tube. It's not a screw inside the tube, more of an inverted bolt head, which is why some one earlier in this thread recommends welding a bolt with the correct head, onto the end of a thin metal bar, with a "T" for a handle at the other end.

I understand you dilema if you have no w/shop book

YouTube - &#x202a;KLR 650 Fork Service Part 1&#x202c;&rlm;

have a look at this and mind this is a different bike and the sizes will most likely be different but the technic is much the same. At least it give you an idea, hopefully

Socks
Reply With Quote
  #22  
Old 24 Jun 2011
R.I.P. 25 November 2021
Veteran HUBBer
  
Join Date: Feb 2010
Posts: 688
As for bleeding the front calliper (i was having problems) somebody suggested taking off the calliper & raising it up to the level of the reservoir (brake line attached) it worked for me.

When i did my forks we "whittled" down a broom handle (shaped it in to a point) until it fitted & would not turn, again it worked for me.

Mezo.
Reply With Quote
  #23  
Old 24 Jun 2011
Registered Users
Veteran HUBBer
  
Join Date: Dec 2008
Location: Denmark
Posts: 1,417
A friend of mine made this tool for replacing the T-handle.
Its a 25x25 steelrod, grinded down a bit in the end, and you can see the part in the forks it needs to hold

Reply With Quote
  #24  
Old 26 Jun 2011
Registered Users
HUBB regular
  
Join Date: Feb 2011
Posts: 70
thanks for the pointers.
im leanding a garage, therefore i want everything to be lined up so that i can do the job in an afternoon. thats why i havent opened up the fork, and then asked the questions.

i got all the air out of the brakes, finally. it seemed that the problem was air in the master cylinder. when i "tapped" the master cylinder easely while pumping it the air "flowed" out and i quickly got pressure. the brake is MUTCH smoother than before.
Reply With Quote
  #25  
Old 26 Jun 2011
Registered Users
HUBB regular
  
Join Date: Feb 2011
Posts: 70
i have been out testdriving afther the brakejob today. the brakes are great.

when i changed the fork oil i filled 545-550 ml in eatch fork to get a stiffest possible ride for commuting. after i found the leak i was afraid that i might have caused it by filling to much oil. i drained some oil(20-30 ml) whiped off the fork and took the bike for a rugged ride. when i got home i couldnt see any signs of a leak. no oil on the legs or gators....

is it possible that i fixed the problem for now by draining some oil?

im going to do the o-ring job, but i would be nice to do it in the wintertimes instead of now...
Reply With Quote
Reply
Page 2 of 2 1 2

« Previous Thread | Next Thread »

Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes
Linear Mode Linear Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
KLE front brake upgrade anyone? rohirim Kawasaki Tech 9 30 May 2013 10:54
bleeding front brakes xt600fun Yamaha Tech 12 28 May 2010 08:11
Rear brake bleeding problem, ? bradley j Yamaha Tech 21 25 May 2009 23:39
Front brake problem Mark Yamaha Tech 3 19 May 2009 23:17
XT front brake pads jbw Yamaha Tech 3 13 Mar 2003 05:22

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

Your ad could be here, on EVERY page of the HUBB, or the whole website, or as many as you like!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.



All times are GMT +1. The time now is 03:02.

Contact Us - Horizons Unlimited Motorcycle Travellers Website - Archive - Privacy Statement - Top