Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > Yamaha Tech
Yamaha Tech Originally the Yamaha XT600 Tech Forum, due to demand it now includes all Yamaha's technical / mechanical / repair / preparation questions.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 23 Oct 2005
big t's Avatar
Registered Users
HUBB regular
 
Join Date: Aug 2005
Location: northern ireland
Posts: 89
3AJ CAMCHAIN

HI All i have noticed at standstill and at 2-2/5 rpm my 43000km 3aj has a distinct rattly noise. below or above this rpm all seems fine.i have checked the tensioner and found it to be at the end of its adjustment.does these symptoms sound like a camchain replacement is needed? if so i plan to go the endless route as described in an earlier post.can i also replace the tensioner blade this way or is it a cylinder head off job? also if i remove the left side engine casing,how much oil can i expect to come out? do i need to drain the oil tank first? any answers greatly appreciated,thanks T
__________________
big T
Reply With Quote
  #2  
Old 24 Oct 2005
Registered Users
Veteran HUBBer
 
Join Date: Jan 2001
Location: Stockholm
Posts: 651
Changing oil is ALWAYS a good idea.
This is definitely a worn cam chain.
Alternatively, lay the bike down on R/H side......
Remove L/H cover and flywheel. Remove cyl head cover but not the cyl head. Replace cam chain.
All greatly facilitated by putting piston at top dead center.

Auke

__________________
Auke
http://aukemarieke.blogspot.com
Reply With Quote
  #3  
Old 24 Oct 2005
big t's Avatar
Registered Users
HUBB regular
 
Join Date: Aug 2005
Location: northern ireland
Posts: 89
thanks auke, can i replace the camchain guides using this method?
__________________
big T
Reply With Quote
  #4  
Old 26 Oct 2005
Registered Users
Veteran HUBBer
 
Join Date: Jan 2001
Location: Stockholm
Posts: 651
Yep, you can. But I have never seen worn guides on a XT / TT, and believe me I have seen a couple of really trashed around engines. So check before you spend the $$ or whatever.

Auke
__________________
Auke
http://aukemarieke.blogspot.com
Reply With Quote
  #5  
Old 26 Oct 2005
big t's Avatar
Registered Users
HUBB regular
 
Join Date: Aug 2005
Location: northern ireland
Posts: 89
well, got the rocker cover off,lhs engine casing off, anyone got any tips on how to lock the flywheel in order to loosen the centre nut ?
__________________
big T
Reply With Quote
  #6  
Old 26 Oct 2005
Registered Users
New on the HUBB
 
Join Date: Oct 2005
Location: Denmark
Posts: 16
Quote:
Originally posted by big t:
well, got the rocker cover off,lhs engine casing off, anyone got any tips on how to lock the flywheel in order to loosen the centre nut ?
Are you able to take & post pictures of your surgery? I imagine there are more than a few of us who have the threat of a camchain change hovering in our near future!


------------------
__________________
Harry Teicher
XT600 43F
Reply With Quote
  #7  
Old 26 Oct 2005
big t's Avatar
Registered Users
HUBB regular
 
Join Date: Aug 2005
Location: northern ireland
Posts: 89
was thinking along the same lines myself! we could have a (how to) picture gallery. seems easier when you can see the actual photos! i will try and post some. T
__________________
big T
Reply With Quote
  #8  
Old 26 Oct 2005
Registered Users
New on the HUBB
 
Join Date: Oct 2005
Location: Denmark
Posts: 16
Thanks! I did a similar thing a couple of years ago on my old MZ two stroker, apparently this helped quite a few people, see:
http://hjem.get2net.dk/bioscience/MZ...shaftseal.html

Harry
__________________
Harry Teicher
XT600 43F
Reply With Quote
  #9  
Old 27 Oct 2005
Registered Users
Veteran HUBBer
 
Join Date: Jan 2001
Location: Stockholm
Posts: 651
Oops, forgot that part...
Easiest is to also remove right hand cover and put a large spanner on crankshaft nut right side, or balancer shaft nut (spanner 30).
Alternatively, use an air tool to remove the nut on the flywheel.
Xcuse me again, this will mean that oil needs to be changed.

I sincerely hope this is the only thing I forgot.

Auke
__________________
Auke
http://aukemarieke.blogspot.com
Reply With Quote
  #10  
Old 27 Oct 2005
big t's Avatar
Registered Users
HUBB regular
 
Join Date: Aug 2005
Location: northern ireland
Posts: 89
cheers Auke, just one more question! with the flywheel off,how do you get the actual chain out? do i need to undo the two camshaft sprocket bolts,remove sprocket and take the chain out from the bottom? sorry for all the questions again! T
__________________
big T
Reply With Quote
  #11  
Old 27 Oct 2005
Registered Users
HUBB regular
 
Join Date: Apr 2004
Location: london england
Posts: 56
Hi hows it going, i'm off from london to oz next year and have just started preventative maintanence on the bike (3aj)my bike was also making the same sort of noise so i took the engine out which took 2 hours and was realy easy to do, and found the cam chain needed changing and also the cylinder was scratched.
my advise to you is if you have a bit of time, take the engine out which was a walk in the park and didn't take hardly any tools, and have a look at the girl. this way your know your bike alot better and have a load more confidence. I'm replacing the guts (valve springs, piston, camchain, gugeoun pin) which has cost 150 notes for the parts so no matter what the out come, its still dirt cheap to sort out
Reply With Quote
  #12  
Old 28 Oct 2005
Registered Users
Veteran HUBBer
 
Join Date: Jan 2001
Location: Stockholm
Posts: 651
Yep, Remove the two bolts on the camshaft sprocket, remove sprocket. The chain can be slid out from the bottom while 'undoing it' from the sprocket on the crank.
Make sure to re-fasten the two bolts on the camshaft sprocket with locktite and make sure to get the timing correct.

Auke

Better ask then destroy ...
__________________
Auke
http://aukemarieke.blogspot.com
Reply With Quote
  #13  
Old 30 Oct 2005
big t's Avatar
Registered Users
HUBB regular
 
Join Date: Aug 2005
Location: northern ireland
Posts: 89
cheers guys, flywheel is refusing to budge!! tried putting some heat on centre but still won,t move! have also noticed some play in left side bearing! think this is gonna be a bigger job than i anticipated. gaskets,camchain and a new set of inlet rubber manifolds have been ordered,so no going back now! thanks again for all your help. no doubt i,ll be seeking more advice on the rebuild. T
__________________
big T
Reply With Quote
  #14  
Old 30 Oct 2005
Registered Users
New on the HUBB
 
Join Date: Oct 2005
Location: Denmark
Posts: 16
Hey T - am following this thread with bated breath!

Harry
__________________
Harry Teicher
XT600 43F
Reply With Quote
  #15  
Old 31 Oct 2005
Registered Users
Veteran HUBBer
 
Join Date: Jan 2001
Location: Stockholm
Posts: 651
Flywheel: make sure to use a well-fitting puller. Leave the nut on, screw it on real tight. Then hit the center bolt of the puller hqrd with a hammer.

Auke
__________________
Auke
http://aukemarieke.blogspot.com
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 13:33.