Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > Yamaha Tech
3AJ Running Rough 3AJ Running Rough
Register FAQ Calendar Today's Posts
Yamaha Tech Originally the Yamaha XT600 Tech Forum, due to demand it now includes all Yamaha's technical / mechanical / repair / preparation questions.
Photo by Ellen Delis, Lagunas Ojos del Campo, Antofalla, Catamarca

I haven't been everywhere...
but it's on my list!


Photo by Ellen Delis,
Lagunas Ojos del Campo,
Antofalla, Catamarca



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 4 Nov 2007
Contributing Member
HUBB regular
  
Join Date: Jun 2005
Location: Sussex, UK
Posts: 75
3AJ Running Rough
Hi Guys, did a top end rebuild recently, set the carb up according to yamaha workshop manual. Bike runs fine going through the gears - but - at about 70mph cruising, the bike feels like it is running out of fuel and occasionally backfires.

The pilot screw was set to two turns out, I adjusted it to 3 turns out- no difference. Any help/ideas would be appreciated.
__________________
Remember what Yoda said\", there is no try, either do or not do\".
Reply With Quote
  #2  
Old 4 Nov 2007
tomwest's Avatar
Registered Users
Veteran HUBBer
  
Join Date: Sep 2006
Location: At the moment:Zanzibar
Posts: 116
Hi.

Have you had a look at your airfilter lately? Had the same problem after I rebuilt my bike,and started it up.After I cleaned the airfilter and adjusted the secundstage opening the bike run fine again.

Cheers.

Tom
__________________
Places to be and things to do, see you all out there!!

Cheers.

Tom.
Reply With Quote
  #3  
Old 5 Nov 2007
*Touring Ted*'s Avatar
Contributing Member
Veteran HUBBer
  
Join Date: Jul 2005
Location: Wirral, England.
Posts: 5,656
The pilot screw will have little effect. Its predominantly only used when the bike is idleing.

Backfiring is a sign of a lean mixture (too much air) but dont confuse this with over run which is common with singles.

Do you have the standard exhaust on ??
__________________
Did some trips.
Rode some bikes.
Fix them for a living.
Can't say anymore.
Reply With Quote
  #4  
Old 5 Nov 2007
Registered Users
HUBB regular
  
Join Date: May 2007
Location: Phoenix
Posts: 68
Were those carby mounting blocks OK? Seems to be a common problem. They will make your bike run lean if they leak.

Steve
Reply With Quote
  #5  
Old 5 Nov 2007
Contributing Member
HUBB regular
  
Join Date: Jun 2005
Location: Sussex, UK
Posts: 75
Hi Ted, I met u at HUUK. (Blue 3aj, camped at the top of the field, bike was burning oil then). Whats over run? and what can I do about a lean mixture
__________________
Remember what Yoda said\", there is no try, either do or not do\".
Reply With Quote
  #6  
Old 5 Nov 2007
*Touring Ted*'s Avatar
Contributing Member
Veteran HUBBer
  
Join Date: Jul 2005
Location: Wirral, England.
Posts: 5,656
Quote:
Originally Posted by Dave O View Post
Hi Ted, I met u at HUUK. (Blue 3aj, camped at the top of the field, bike was burning oil then). Whats over run? and what can I do about a lean mixture
To start with, put the pilot back where it was. As long as it starts fine and idles fine with the stock pilot setting, just leave well alone !

Did you sort the oil leak ??.. Perhaps it was just condensation ???

The best way to determine if its running lean or rich is to find a garage with a gas analyser to "sniff" your exhaust.

Failing that, you could try moving the little Circlip on the needle adjustment on the carb. Dropping it down a notch will make the open throttle position a little richer.

Have you got the standard exhaust on ??? Is the air filter clean ?? are the carb rubbers in good condition and tight ??

Overrun is slight popping when you shut the thottle on a big single "bom bom bom" etc

I would set your carb and bike to as close as stock as possible then make small adjustments to the fueling.

Also check your tank is breathing ok (no trapped breather pipes etc)
__________________
Did some trips.
Rode some bikes.
Fix them for a living.
Can't say anymore.
Reply With Quote
  #7  
Old 14 Feb 2011
Registered Users
New on the HUBB
  
Join Date: Feb 2011
Location: Edinburgh
Posts: 9
Rough running ttr 600re
Hi Guys,
I have a ttr600 re 05 with 1000miles on it.
It started to :like run out of petrol: at high speed like going on reserve.
Plenty of fuel, i only get this at high speed.
I changed the plug to an iridium one and checked and taped the ht lead onto coil and new ht cap.
Cleaned the filter and oiled it.
Fresh fuel.
Any ideas, any help will be appreciated.
Cheers Chris....
Reply With Quote
  #8  
Old 14 Feb 2011
Registered Users
Veteran HUBBer
  
Join Date: Dec 2008
Location: Denmark
Posts: 1,417
Does the gas tank vent properly?

Nothing worse than a bike that doesn't work properly
Reply With Quote
  #9  
Old 14 Feb 2011
Registered Users
Veteran HUBBer
  
Join Date: Jan 2001
Location: Stockholm
Posts: 651
and some other causes ...
Checking the tank vent is definitely a good one.
Then, there is a little filter on top of the float valve seat, inside carb. It is so tiny as to clog up swiftly. Just remove it, then take out into woods and shoot it, then burn it. Then install an inline fuel filter.
Third, clean air filter, it might look clean but that does not mean it is.

Btw, 2005 and only 1000 miles - that is a lot of just standing - chances are something else in your carb has gunked up with old fuel.

Auke
__________________
Auke
http://aukemarieke.blogspot.com
Reply With Quote
  #10  
Old 15 Feb 2011
R.I.P. 25 November 2021
Veteran HUBBer
  
Join Date: Feb 2010
Posts: 688
Quote:
Originally Posted by Jens Eskildsen View Post
Does the gas tank vent properly?
Do 3AJ`s have a tank vent then? where would that be located? i thought it just vented through the gas cap.

Mezo.
Reply With Quote
  #11  
Old 15 Feb 2011
Registered Users
Veteran HUBBer
  
Join Date: Dec 2008
Location: Denmark
Posts: 1,417
Ueh yeah, they should just vent through the cap... but who knows if it works properly.

I have a 23ltr acerbis tank on, which has a different cap on, sorry for misleading.....

Have just seen the 1000miles since '05. I think the carb is full of goo.
Reply With Quote
  #12  
Old 15 Feb 2011
Registered Users
New on the HUBB
  
Join Date: Feb 2011
Location: Edinburgh
Posts: 9
Thanks guys,
I check the breather pipe on top of the filler cap its clear. how do i know if the filler cap is venting right?
I stripped off the carb nightmare job. There must be an easier way than undoing the clips forcing the airbox pipes back into the air box, as well as undoing the throttle cables?????
Anyway now removed, (two rubber o-rings about the size of a 1p and one really small one fell on the floor dont know where they came from ) i unscrewed the bottom of the primary where the float bowls are i see the jets, all looks clean. I sprayed up the jet with brake cleaner anyway. Where is this little sod of a filter located, and how do i remove it.
Thanks again any help will be appreciated.
Cheers Chris..........
Reply With Quote
  #13  
Old 15 Feb 2011
Registered Users
Veteran HUBBer
  
Join Date: Jan 2001
Location: Stockholm
Posts: 651
Huh?
Is it a 3AJ (tenere) or a TT600RE?
Anyway, if you'd like to know where the O-rings came from try to get hold of an exploded biew of carb and inlet rubbers etc. I don't know about p's, I'm from Euro / swedish crwon country.
The filter: you took off the float bowl, so you see the jets and the float. The float actuates a needle which falls into a little copper tube. This is the float valve seat. If remove the float (carefully tap out the hinge pin) you can remove the little screw holding the seat in place. Then, VERY CAREFULLY WITHOUT FORCE retract the seat from carb body. You'll see the little bugger (=filter) on top of the seat. Just unclick.
Hint: there is an O-ring between carb body and float bowl. It is ribbed.

Good luck! A
__________________
Auke
http://aukemarieke.blogspot.com
Reply With Quote
  #14  
Old 15 Feb 2011
Registered Users
Veteran HUBBer
  
Join Date: Dec 2008
Location: Denmark
Posts: 1,417
The original OP had problems with an 3aj (back in 2007)

This thread was recently revived regarding a question for a tt600...So yeah, not easy to follw what the %&(# is going on =)

The vent should be able to let air into the gastank, so it wont build uderpressure, which would work against the vacuumoperated fueltap
Reply With Quote
  #15  
Old 16 Feb 2011
Registered Users
New on the HUBB
  
Join Date: Feb 2011
Location: Edinburgh
Posts: 9
Thanks guys,
I have removed the little filter, and built the carb back up after cleaning all the jets.
The rubber o-rings that fell on the floor was from the over flow pipes on the carb to keep them together. No big deal they will go back on after in reinstall the carb back on the bike.
Hopefully this clean up will cure the rough running.
I will post on the out come.
Cheers Chris
Reply With Quote
Reply

« Previous Thread | Next Thread »

Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
GS running baddle with Mexican fuel - looking for ideas. strsout Route Planning 27 2 Nov 2007 17:54
3AJ Headlight Question MotoXT Yamaha Tech 4 11 Apr 2007 21:03
Info needed on boats running from Cartagena to Panama - 2007 Iain Central America and Mexico 12 22 Jan 2007 20:19
TTR running rough bolla Yamaha Tech 2 1 Aug 2005 02:38
R100GS running rough harvey BMW Tech 6 18 Apr 2002 21:27

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

Your ad could be here, on EVERY page of the HUBB, or the whole website, or as many as you like!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.



All times are GMT +1. The time now is 04:51.

Contact Us - Horizons Unlimited Motorcycle Travellers Website - Archive - Privacy Statement - Top