Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > Yamaha Tech
Yamaha Tech Originally the Yamaha XT600 Tech Forum, due to demand it now includes all Yamaha's technical / mechanical / repair / preparation questions.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 23 Jan 2009
Registered Users
HUBB regular
 
Join Date: Oct 2007
Location: Greece
Posts: 38
2003 ΧΤ600Ε - Head noise (Piston Damage)

Hi,

I have a problem with my ΧΤ600E. The engine has very low miles(racing engine), recently rebuilt, 12.4:1 compression, forged piston, webcams 282o cam, ti retainers, uprated valve springs, new cam sprocket-chain.

Recently, it started making a ticking noise from the head, mainly in idle (1600-1800rpm). In higher revs, the noise from the exhaust doesn't allow me to hear for the ticking. It sound a bit louder than incorrectly setup valve clearances, but i checked and adjusted them, with no change.

The engines runs fine, idles very good(for this cam), no-oil burning and generally nothing strange than the ticking noise.
Inside the valve cover (seeing from the port for the adjusters), everything seems fine and neat.

I read about cam chain, but as i have changed it recently, together with the sprocket, i don't think it's the problem.

What else it could be?

Last edited by mech5107; 6 Sep 2009 at 19:52.
Reply With Quote
  #2  
Old 5 Sep 2009
Registered Users
HUBB regular
 
Join Date: Oct 2007
Location: Greece
Posts: 38
Recently we had some time to work on this engine...

It has done some tough races during the season and in one of them an oil line leaked and it lost most of its oil, but it was rapidly stopped so no more harm has been done.

After the season, with no rebuilt, we had some testing and the problem that i describe above has started. (the rattling)

So today we removed the engine and disassembled it.

That's what the piston looked like...




It's only this side, at the opposite face there is some scars, but not serious. The barrel has some scratches but not as bad as the piston.

I have suspected the oil-pump, but i checked as the manual say, by removing the bolt at the oil filter housing, and oil come out right away, but not with much pressure. Also in the engine, if i open the drain plug some oil comes out, but as much as ~250ml.
Finally, as i found out today, on the head, under the camshaft, the gallery there had a lot of oil and the cam is in very good condition.
So i think that the pump is ok.

I also found some damage to the piston pin, at the point that is in the rod, and the piston has also some damage at the points where the pin is.

Why did this happen? How should i eliminate it?
I will probably go for an over-sized piston and barrel machining, but i would like to take an opinion on what's the problem.
Reply With Quote
  #3  
Old 5 Sep 2009
Tenere Tom's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Aug 2007
Location: Leeds UK
Posts: 449
I've got a piston/barrel like that!!! (see my thread in the archives).

It was a simple case of lack of oil.

Have you got the full spec of the engine?

I'm holding onto a XT600 hybrid lump that I'm going to graft into a fizzy or something stupid.
__________________
Tom
I'm a country member...
Reply With Quote
  #4  
Old 5 Sep 2009
Registered Users
HUBB regular
 
Join Date: Oct 2007
Location: Greece
Posts: 38
What you mean the full spec, it's as i have written in the first post.

I thought about the oil, but the facts i have written in the second post, i think that exclude the lack of oil.
Reply With Quote
  #5  
Old 5 Sep 2009
Registered Users
Veteran HUBBer
 
Join Date: Dec 2008
Location: Denmark
Posts: 1,417
Theres an internal net-oilfilter, you might wanna check that.

Take of the engineguard, and the plate arund the front of the frame, where you drain the oil from the chassis (in lack of better word)

Take of the oil line, and use a size 27 key (thats what it is here in Denmark europe, dont know your're messures) and screw out the filter. It's screwed in there real tight, something like above 100nm. Rock it, and put all ya' weight in it, and it will come of.


The filter shouldn't be clogged, mine has done 70k km and i dont think it has ever been cleaned, and there was next to nothing in it.

But its worth trying.
Reply With Quote
  #6  
Old 5 Sep 2009
Registered Users
HUBB regular
 
Join Date: Oct 2007
Location: Greece
Posts: 38
Sorry, i forgot to mention it...

The engine is not on a bike, it's on a small single seater car.
i use a custom oil tank (~3.5L capacity) with hi-pressure oil-lines and in-line oil cooler. So no in line oil filter.
Reply With Quote
  #7  
Old 5 Sep 2009
Tenere Tom's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Aug 2007
Location: Leeds UK
Posts: 449
Quote:
Originally Posted by mech5107 View Post
Sorry, i forgot to mention it...

The engine is not on a bike, it's on a small single seater car.
i use a custom oil tank (~3.5L capacity) with hi-pressure oil-lines and in-line oil cooler. So no in line oil filter.
Is the oil tank above the engine like it would be on a bike?
That could be the problem - there is deffo a lack of oil somewhere!!!
__________________
Tom
I'm a country member...
Reply With Quote
  #8  
Old 6 Sep 2009
Bobmech's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Sep 2008
Location: BOP , New Zealand
Posts: 183
I've seen pistons looking similar to that caused by overheating, so may not have sufficient air flow?
Bob
__________________
Remember that Assumption is the mother of all f**k-ups.
Reply With Quote
  #9  
Old 6 Sep 2009
bacardi23's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Sep 2007
Location: XXX<-Portugal->Azores->Santa Maria (island)
Posts: 1,544
Wow... That's some nice work ya got there :\

It does look like you got some overheating due to not enought oil flow or not cool enough.

Bobmech mentions a good point...how about improving the airflow?
some fiberglass work isn't that hard and would probably help to cool down your engine...

Also, if you could fit a oil radiator on the front of that car with fiberglass "wind tunnel" would surely cool down that oil

There are some older XT's that have some small oil radiators...good starting point?


Vando
Reply With Quote
  #10  
Old 6 Sep 2009
Registered Users
HUBB regular
 
Join Date: Oct 2007
Location: Greece
Posts: 38
Quote:
Originally Posted by Tenere Tom View Post
Is the oil tank above the engine like it would be on a bike?
That could be the problem - there is deffo a lack of oil somewhere!!!
Yes, it's over the engine. The bottom of the tank is at the level of the head. But i don't think that it would be a problem, if it was sitting lower.
The oil will flow to the engine.

I must say again, that the engine is in very good condition except piston-barrel.

The cam, rockers, gearbox, crank are in excellent condition.

Quote:
Originally Posted by Bobmech View Post
I've seen pistons looking similar to that caused by overheating, so may not have sufficient air flow?
Bob
The airflow is a possibility, but judging from the oil-temp readings, i thought it's ok.

Quote:
Originally Posted by bacardi23 View Post
Wow... That's some nice work ya got there :\

It does look like you got some overheating due to not enought oil flow or not cool enough.

Bobmech mentions a good point...how about improving the airflow?
some fiberglass work isn't that hard and would probably help to cool down your engine...

Also, if you could fit a oil radiator on the front of that car with fiberglass "wind tunnel" would surely cool down that oil

There are some older XT's that have some small oil radiators...good starting point?


Vando
I have oil temp sensor and it reads about 90-93oC when idling for some time and the highest i have seen is 103oC. I don't think that it's that bad.

And yes, i have oil-cooler, in line with the tank. The only thing i would think about the oil-cooler is to be in the wrong place. It's between the oil-tank and the engine, so to have the coolest possible oil entering the engine. I was thinking that i had problem with the oil pressure, but as i wrote before, oil comes out when removing the bolt from the oil-filter housing, and there was a lot of oil under the cam when i opened the engine.

Where does the "standard" oil coolers connect to the engine?
Reply With Quote
  #11  
Old 6 Sep 2009
Registered Users
HUBB regular
 
Join Date: Jun 2008
Location: Pietermaritzburg
Posts: 63
On my srx, xt engine based, the oil cooler is in line with the return oil feed and i believe that to be the standard yamaha system. Iv certainly read NOT to put one inline with the oil supply feed.
Reply With Quote
  #12  
Old 6 Sep 2009
Registered Users
Veteran HUBBer
 
Join Date: Aug 2009
Location: Dorset UK
Posts: 395
Wot size are the cooler lines..... if too big/small this can effect the flow/pressure.

As its hi-comp.... heat will be a big issue.... even with the temp readings....

Ideally you want oil to be at 85-90 degs. Once it boils it degrades fast.

Sure its not running rich at full throttle... as in "wash out" of the bores?

Running a race engine, I'd have thought an upgraded pump would be wise.
Reply With Quote
  #13  
Old 6 Sep 2009
Registered Users
HUBB regular
 
Join Date: Oct 2007
Location: Greece
Posts: 38
The oil-lines are ~10mm internal diameter. The stock barbs I've got it's 9.5 internal.

I use fuel-injection and a wideband O2 sensor, it's tunned very well.

Also some extra photos

The front face of the piston...There's damage, but not as the back.


The pin...also some damage to the rod small-end.



The pin pockets on the piston. There are those deformations that i don't know why occurred...the pin-piston tolerance seems ok (i will check it), no movement.

Reply With Quote
  #14  
Old 6 Sep 2009
Registered Users
Veteran HUBBer
 
Join Date: Dec 2008
Location: Denmark
Posts: 1,417
100 degrees aint bad for a big aircooled single.
How about to much throttle when the oil isn't up in temperature?
Reply With Quote
  #15  
Old 6 Sep 2009
Registered Users
HUBB regular
 
Join Date: Oct 2007
Location: Greece
Posts: 38
I need to hold it at about 3000-3500 until it gets to 40oC oil-temp (then it idles nicely at 1800-2000) and usually the temp is 80+ when driving on high load.

As i told, the temp is between 85-95oC. I rarely see over 100 and this is due to very hot weather and car stopping and waiting after hard run (driver change, incident on the track, etc).
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Engine noise Gawain Yamaha Tech 7 6 Sep 2009 08:59
noise on head zisis Yamaha Tech 8 20 Dec 2008 15:43
Engine noise :-( spakur KTM Tech 4 18 Jun 2008 19:17
34L strange noise dougM Yamaha Tech 0 6 Jan 2003 08:44
Weird Noise OXXT Yamaha Tech 1 16 Feb 2002 23:31

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 15:33.