Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > Tech
Tech ALL bikes: "Generic" tech questions and answers. Maintenance, general discussions etc.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 1 Oct 2011
Registered Users
HUBB regular
 
Join Date: Oct 2009
Posts: 32
sand blasting the frame

hi.

i have in mind to stripe my dr a sand blast it and re spray it coz it looks like it could do with it and mostly coz im not riding it and its on a sorn and i fancy a poject.

anyone know anything about doing this.?
you think its worth doing it myself or just paying for it?

its not really my project if i just pay for it.. but thinking ill spend more on equepment than paying someone to do it.

thanks
Reply With Quote
  #2  
Old 1 Oct 2011
Registered Users
Veteran HUBBer
 
Join Date: Jan 2009
Location: Bassett, Nebraska
Posts: 276
Hi Jimmy,

Yes you will likely spend more on sand blasting equipment than hiring out the job on a small job like a moto frame. But who says you have to sand blast the frame? If you have more time than money there are other alternatives. You don't have to sand off good paint on a bike frame to change color. All you need to do is scuff the good paint with a fine grit sandpaper, feather out the chips and sand down to bare metal any small rust spots. Hang it in your shed from some wire and prime and paint with quality paint and you can achieve quite good results. Just be careful to mask off the headstock and any threaded holes to avoid clogging with paint.

Of course we all learn that it is often cheaper to buy a well restored bike that some poor anal retentive guy with a garage floor so spotless you could eat off it obsessed on than to do it ourselves. But what fun is that?

Cheers,
John Downs
__________________
South America and back on a 250 Super Sherpa Minimalist Adventure http://advrider.com/forums/showthread.php?t=831076
Reply With Quote
  #3  
Old 1 Oct 2011
Dodger's Avatar
Large Golden Member
Veteran HUBBer
 
Join Date: Aug 2005
Location: BC, Canada
Posts: 1,085
It's not worth the time and effort to sandblast an old bike frame .
You'd have to strip it right down and make sure that before you paint it that the abrasive is cleaned out of every nook and cranny ,chances are that it will get into swing arm or head stock bearings and cause you grief later on .

Better IMHO to use paint stripper or sand and feather the rough areas and apply a good hard finish frame paint like PJ1 if it's still available .
__________________
Blessed are the cracked, for they let in the light. - Spike Milligan
"When you come to a fork in the road ,take it ! When you come to a spoon in the road ,take that also ."
Reply With Quote
  #4  
Old 1 Oct 2011
Registered Users
Veteran HUBBer
 
Join Date: Nov 2008
Location: poole dorset
Posts: 148
I'm currently striping my frame of paint on my restoration project. I'm using nitromorse paint stripper and when I spray it I'm going to use black hammerite with maybe a touch of plastersiser in it. A paint spayer friend put me onto this and said it goes really hard but stays a bit flexible if that makes sense.. Dont use normal car spray paint its not really designed for tubing and chips easy..

Where do you live? I have a compressor and spray gun if your near Poole, England..haha
Reply With Quote
  #5  
Old 1 Oct 2011
Registered Users
HUBB regular
 
Join Date: Oct 2009
Posts: 32
ok john.

thanks for that.

think i would prefer to do it myself as you have explained.

i have more time than money thats for sure.

so 'scuff' you meaning sand with sand paper.
and spray with decent paint from the can yes?

sweet.

thinking i might start after christmas.
Reply With Quote
  #6  
Old 1 Oct 2011
Registered Users
HUBB regular
 
Join Date: Oct 2009
Posts: 32
i live on the north norfolk coast.
burnham market

not sure where poole is.

so its best im guessing to use a compresser and spray gun.

ive used spray from a can before, from halfords and it dont do the job really.
Reply With Quote
  #7  
Old 1 Oct 2011
Registered Users
Veteran HUBBer
 
Join Date: Nov 2008
Location: poole dorset
Posts: 148
I'm on the south coast haha bit of a trek mate.. Yeah I would use a compressor and spray gun you can get some fairly good deals. Nothing fancy just a small compressor but make sure if you get one it has a regulator to adjust the working pressure for the spay gun.. My compressor was about £80 and the gun about £20 but I use the compressor all the time so well worth it..
Reply With Quote
  #8  
Old 1 Oct 2011
Registered Users
HUBB regular
 
Join Date: Oct 2009
Posts: 32
so the way is.
1.sand it down and take all rust of and edges.
2. prime it... now would this go through the spray gum,... or from a can?
3. give a decent coat of quality paint.

anything after this.
is there no layer after the paint?

cheerrrs
Reply With Quote
  #9  
Old 1 Oct 2011
Registered Users
HUBB regular
 
Join Date: Oct 2009
Posts: 32
speaking about tools and equipment.

do you guys know about bidspotter uk

buisnesses going bankrupt and you can get some pretty good deals.

though you have to travel to pick things up.

but worth a look.

www.bidspotter.co.uk
Reply With Quote
  #10  
Old 1 Oct 2011
Registered Users
Veteran HUBBer
 
Join Date: Nov 2008
Location: poole dorset
Posts: 148
I would take it back to bare metal with paint stripper and a wire brush is a 4" grinder and then depending on what paint you use you may need a primer. I would try to avoid primer if possible and go with a hard paint (primer may be softer and chip off). There is an acrylic spray can paint you can use but I find its still a bit on the soft side. (I bought some from ebay) I have used this on air boxes and bits that wont come into direct conact with flying stones etc..

Thanks ffor the heads up on bidspotter, not seen it before :-)
Reply With Quote
  #11  
Old 1 Oct 2011
Registered Users
HUBB regular
 
Join Date: Oct 2009
Posts: 32
jim. you saying you would use hammerite. Where you going to be getting theis paint from and will you be using your spray gun to do this?

so your taking your bike to bare metal and then just spray a few coats of hammerite on.?

whats your project jim?
what bike you working on?
Reply With Quote
  #12  
Old 1 Oct 2011
Registered Users
Veteran HUBBer
 
Join Date: Nov 2008
Location: poole dorset
Posts: 148
I will be using the smoothrite version I think it is, just from B&Q add some thinners and spray it from the gun building up thin coats of paint. You can lightly sand it with a really fine paper just to flatten it off before the final coat. Depends how fussy you want to be really..

I'm restoring a 1976 Honda cb500t for a bit of fun. I need to get it done so I can get on with building a light weight trail adventure bike..
Reply With Quote
  #13  
Old 4 Oct 2011
gixxer.rob's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Mar 2008
Location: Back in Melb
Posts: 287
The finished product

It really depends on what you want the finished product to look like.

You can just remove all the loose paint, rust and repair any other damaged surface, prep and paint over the top. This will be fine but be under no illusions that this will not be as good as stripping to bare metal and repainting with quality paints or better still powder coating.

Having done a frame back to bare metal with paint stripper, rotary wire brushes, sanders and hand sanding. It took a long, long time and if given the a choice again I would get it sand blasted. Blocking off/packing/closing up the bearings is not that hard. If worst comes to worse and you do damage a bearing replacing a bearing at this stage (stripped down bike) is not a big deal in terms of what you will do from there.

It all depends on how long you have and what you want the finished product to look like/quality of finish.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Sand in the UK? henryuk Travellers' questions that don't fit anywhere else 12 10 Jan 2011 21:59
driving in sand, picking up dropped bike in sand? monkii North Africa 2 31 May 2007 04:57
sand ladders Babsickle TRAVEL Equipment for Sale / Wanted 2 6 Sep 2004 01:19
Sand! Sam Rutherford North Africa 0 7 Jan 2003 22:02
Riding in sand pierresas North Africa 2 23 Jan 2002 23:01

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 15:29.