Go Back   Horizons Unlimited - The HUBB > Regional Forums > Northern and Central Asia
Northern and Central Asia Topics specific to Russia, Azerbaijan, Armenia, Georgia, Kazakhstan, Uzbekistan, Tajikistan, Kyrgyzstan, Turkmenistan, Mongolia, China, Japan and Korea
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 19 Aug 2012
Registered Users
HUBB regular
 
Join Date: Feb 2009
Location: Washington DC
Posts: 53
Stuck in Tashkent, need chain tools

Hello all,

My wife and I are half way around the world in Tashkent on our F800GS and loving our trip so far. Today we started some maintenance today, replacing the front and rear sprockets and intending to replace the chain. We got to the point where we were installing the new chain and found, to our dismay, that we don't have the right chain tool. I know, stupid mistake. Wrong chain or wrong tool, whatever the case we are stuck.

Does anyone know where we can find someone near Tashkent with a chain tool that can punch the rivets out of a DID 525 VX chain and then rivet the master link? Maybe a traveller is near or someone knows a local mechanic with a chain tool? Would a bicycle repair shop be able to help? Any suggestions?

Thanks for your help.

Jeff and Si
Reply With Quote
  #2  
Old 19 Aug 2012
Registered Users
Veteran HUBBer
 
Join Date: Jan 2009
Location: Bassett, Nebraska
Posts: 276
Hi Jeff,

Hopefully you will find a traveler with a 525 chain tool. Failing that you will have to resort to third world caveman technique.

When I needed to remove a link from a stretched chain on a rental bike in Costa Rice, this consisted of stopping at a roadside transmission repair shop where the owner Señor Pollo cut the chain off with a metal blade in an angle grinder, carefully ground the heads of chain rivet, used a hollow transmission input shaft against one side of the chain while he used a ground down pin punch to drive the pins out of the chain, remove a link, reassemble on the bike and had me hold a block of steel on one side of the chain while he carefully peened over the pin.

I'm not saying you should do this, more as information for someone slightly more desperate who may read this.

525 DID chains and tools can be rare as hen's teeth in the third world. More likely in Tashkent than a village in the mountains though.

I should think that a large C-clamp could be modified to work as a pin press in a pinch.

Others may have ideas.

Best luck.

Kindest regards,
John Downs
__________________
South America and back on a 250 Super Sherpa Minimalist Adventure http://advrider.com/forums/showthread.php?t=831076
Reply With Quote
  #3  
Old 19 Aug 2012
Registered Users
HUBB regular
 
Join Date: Feb 2009
Location: Washington DC
Posts: 53
Thanks John. And good timing. I was just trying to figure out if a DID brand chain breaker/riveter is really needed for a DID 525 chain. DID seems very particular, a little contradictory, and generally confusing on their site: D.I.D. Racing Chains and DirtStar® Rims

Reading reviews and forums around the web has given me the impression that other chain tools generally work fine with any brand of chain but there are quite a few cases where all manner of chain tools break on first or second use.

What's your impression on this? I would hate to unnecessarily turn away a traveller with a perfectly good Motion Pro chain tool...

Quote:
Originally Posted by John Downs View Post
Hi Jeff,

Hopefully you will find a traveler with a 525 chain tool. Failing that you will have to resort to third world caveman technique.

When I needed to remove a link from a stretched chain on a rental bike in Costa Rice, this consisted of stopping at a roadside transmission repair shop where the owner Señor Pollo cut the chain off with a metal blade in an angle grinder, carefully ground the heads of chain rivet, used a hollow transmission input shaft against one side of the chain while he used a ground down pin punch to drive the pins out of the chain, remove a link, reassemble on the bike and had me hold a block of steel on one side of the chain while he carefully peened over the pin.

I'm not saying you should do this, more as information for someone slightly more desperate who may read this.

525 DID chains and tools can be rare as hen's teeth in the third world. More likely in Tashkent than a village in the mountains though.

I should think that a large C-clamp could be modified to work as a pin press in a pinch.

Others may have ideas.

Best luck.

Kindest regards,
John Downs
Reply With Quote
  #4  
Old 19 Aug 2012
Contributing Member
HUBB regular
 
Join Date: Jun 2012
Location: Alberta, Canada
Posts: 60
My two cents re: Motionpro Chain Tool

I have used, and have broken, a Motionpro chain tool while on a trip down to California from Alberta, Canada. If you read very carefully and follow the instructions exactly, you can break and rivet the master link without breaking the tool. The dealer warned me that they break easily and even explained what causes them to break but I broke mine while pushing the pin out. After having broken it, it was easy to understand why it broke but of course it was too late. The riveting pin is much easier to use and is far less likely to be a problem. I replaced the broken part easily and relatively cheaply but I'm also at home so that's a whole different game than what you'll deal with. If I was needing to replace my chain on the road again, I'd use an angle grinder to break it if available before I tried the tool again. Riveting with the tool is much easier and less risk of breaking. Take your time and really understand the instructions before you start and don't rush the job and you'll be fine though.
Reply With Quote
  #5  
Old 19 Aug 2012
Registered Users
HUBB regular
 
Join Date: Feb 2009
Location: Washington DC
Posts: 53
Thanks Roger. Which MP chain tool did you have? The PBR? Motion Pro - PBR Chain Tool

I may order either the DID KM501E or Motion Pro PBR chain tool, a couple extra riveted master links and a couple clip master links and have them all shipped to Tashkent. Shipments can supposedly get here in 5 days but I'm a little wary of customs and other random delays.
Reply With Quote
  #6  
Old 19 Aug 2012
Registered Users
Veteran HUBBer
 
Join Date: Jan 2009
Location: Bassett, Nebraska
Posts: 276
Either tool will work. I have the Motion-Pro and what Roger said is true. Although the tool works fine for pressing on plates and riveting replacement hollow or soft tip rivets, it has a hard time pressing out the old rivets when trying to break a chain. It is easier as he suggests to grind off the old rivet heads with a grinder before pressing them out. Or cutting the old chain off with bolt cutters if you are replacing it.

I looked at the picture of the DID K501E tool and it can cut plates off so perhaps a bit more versatile.

Alas, fixing flats and replacing chains wasn't on the curriculum at University. I've had to learn the hard way.

Safe travels.

Best,
John Downs
__________________
South America and back on a 250 Super Sherpa Minimalist Adventure http://advrider.com/forums/showthread.php?t=831076
Reply With Quote
  #7  
Old 19 Aug 2012
Registered Users
Veteran HUBBer
 
Join Date: Feb 2006
Posts: 1,598
Would it be possible to use an old non did or O ring chain. one that has a split link? it would give you the ability to continue your journey without delay.
I ride an Enfield so can't use modern chains. I always carry at least one spare chain and extra split link, but these old chains disappear quickly. 8k miles is quite a good life for them. Wish I could use the modern chains, However the split link allows me to change a chain in about 5 minutes using just a screwdriver and pliers.

My BMW made me forget about chains, one thing I do miss is the shaft drive
Reply With Quote
  #8  
Old 20 Aug 2012
Contributing Member
HUBB regular
 
Join Date: Jun 2012
Location: Alberta, Canada
Posts: 60
Motionpro chain tool

Yes, I have the PBR kit. I also carry an old style clip type master link with the o-rings that I got at the local Honda shop as an emergency repair option but would only use it to get me through a pinch. The thought of having a chain come loose and break the crankcase while on a trip (or anywhere for that matter) is just not something I can live with. I was also able to find a 525SRX-SLJ screw type connecting link from EK (Enuma Chain Mfg. Co., LTD) part number 706429 from Parts Canada that doesn't require riveting. I haven't tried it yet but it looks promising. The only issue I see with it is potential for side clearance. The little nuts stick out about 1/4" from the side plate. Hope your repairs go well! My trips are limited presently to 7-10 days so any down time in a parking lot is to be avoided if at all possible. I spend the winters up here tearing the bikes apart and fixing ANYTHING that looks iffy. Summers are strictly for fun...
Reply With Quote
  #9  
Old 20 Aug 2012
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2007
Location: Rockhampton, Australia
Posts: 868
Quote:
Originally Posted by roger2002 View Post
I was also able to find a 525SRX-SLJ screw type connecting link from EK (Enuma Chain Mfg. Co., LTD) part number 706429 from Parts Canada that doesn't require riveting. I haven't tried it yet but it looks promising. The only issue I see with it is potential for side clearance. The little nuts stick out about 1/4" from the side plate. ..
I have used those on my bike for many years as I love EK chains. I still have one of these as an emergency link, even though I am overseas with a different brand chain. The think is, it is simple to use and those bits that stick out have never caused me a drama on my Vstrom

Cheers from Kazakhstan
TravellingStrom
__________________
www.travellingstrom.com
Reply With Quote
  #10  
Old 20 Aug 2012
Registered Users
HUBB regular
 
Join Date: Feb 2009
Location: Washington DC
Posts: 53
Thanks for all the advice.

We've ordered a DID KM501E chain breaking+riveting tool, 19mm and 27mm wrenches for use with the tool, a metal file to file off the rivet heads and adjust length of new chain, and two compatible clip and two compatible rivet master links.

Today we'll visit the VM Biker Bar and several auto shops to see if anyone can help size and rivet the new chain. If so, we'll remove the swingarm, install the closed chain.

We'll also ask around for spare clip style master links that we could use to get us through our tighter visa schedule.

If anyone hears of a biker coming through Tashkent in the next week two might have a chain tool, please let them know about us.

The extra expense is painful but this shipment gives us a fall back fix in case we don't find any way to reliably work on this chain over the next few days. If we're back in business sooner then we'll have our shipment forwarded to a new address and will be better prepared next time.

Any other ideas? Please keep them coming!

Thanks again,
Jeff and Si
Reply With Quote
  #11  
Old 20 Aug 2012
Contributing Member
Veteran HUBBer
 
Join Date: Oct 2007
Posts: 374
This has worked for me.

Hi I have cut the heads off the rivets on a DID 525 EK chain with hacksaw before (about half hours work)

I have also one more than occasion flared the heads with lock pliers (Vise Grips). In the first occasion this lasted for the life of the chain. The second time has done near on 15,000kms, without failure.

This method doesn't give the same nice flare as tool does, but remember it the is not much load on this part of the chain, all you need too do is make sure it stays on there nice and snug. May sound dodgy, but desperate times wtc.
Reply With Quote
  #12  
Old 20 Aug 2012
colebatch's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Nov 2004
Location: London / Moscow
Posts: 1,913
had a chain snap on me on the BAM Road in 2009. fitted the new chain in situ and flared it using a screwdriver as a flaring tool, a rock for a hammer to hit the screwdriver and another rock being held behind the chain,

As craig says, there is very little lateral load on the rivet, and the tiniest bit of flaring will hold it all together for the life of the chain
Reply With Quote
  #13  
Old 20 Aug 2012
Nigel Marx's Avatar
Super Moderator
Veteran HUBBer
 
Join Date: Oct 2000
Location: South Island, New Zealand
Posts: 798
For the first fifteen years I rode motorbikes, I didn't even know there was such a thing as a chain tool. I only ever used a file or angle grinder and a punch.

Cheers

Nigel in NZ
__________________
The mouth of a perfectly contented man is filled with . -- 2200 BC Egyptian inscription
Reply With Quote
  #14  
Old 21 Aug 2012
Registered Users
HUBB regular
 
Join Date: Feb 2009
Location: Washington DC
Posts: 53
This is the inspiration we need! Thanks all. We just don't have the experience to know what's a clever workaround and what's plain dumb, so hearing what has worked well enough for others is very helpful indeed. We don't want to be stuck on a mountain pass in Pakistan because we were foolhardy in Uzbekistan!

Thanks again.

Oh, and we stopped by the VM Bar here in Tashkent a couple times today. It's allegedly a biker bar but we have reason to believe there are no more than four bikers in the area so maybe that explains why the bar was closed both times we stopped by. Wondering if it went out of business. On the other hand today is a gov't holiday for the end of ramadan so we'll try again tomorrow night. We're quite enjoying the city anyway.
Reply With Quote
  #15  
Old 21 Aug 2012
Registered Users
HUBB regular
 
Join Date: Feb 2009
Location: Washington DC
Posts: 53
How about this. We have a Motion Pro T-6 chain tool (official instructions: "doesn't rivet!" - http://www.motionpro.com/documents/p...0_I08-0358.pdf) which we used to break the old chain. We also have a Leatherman with a file which we just used to file the head off a rivet on the new chain and then the chain tool again to break two links off, making the new chain the correct length. The master link that we have has dimpled pins. I include this because we read there are master links with non-dimpled pins that are impossible to rivet without special tools. Anyway, the MP chain tool has a flat headed extractor pin that pushes chain pins out. Other MP chain tools that actually rivet come with a second pin with a semi-rounded head. We were thinking that maybe we could file the extractor pin head to round it out then use the chain tool to attempt to deform the dimpled pin heads. Something akin to another roadside method we read on ADV, seating a hard BB in the dimple and clamping down with pliers. Except instead of clamping we'd be wrenching the chain tool. On the other side of the chain we'd use MP's slotted back plate to hold the pins and chain plate.

Does anyone see any potential pitfalls with this approach? It must have less risk of screw-up than two rocks and a screw driver but we are trying to be cautious since we only have one master link.

Thanks again all!

Jeff and Si
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Drive Chain for 88 xt600 tenere floyd Yamaha Tech 12 3 Jul 2012 15:44
Which spare parts and tools to take along on a journey with a Moto Guzzi V7 Classic? Guzzi_Ed Other Bikes Tech 5 5 Jun 2012 14:20
XT600E cam chain life? The other Paul G Yamaha Tech 5 6 May 2012 20:50
Slack Drive Chain in Peru Adelaide to Anchorage The HUBB PUB 4 20 Apr 2012 16:42
Clutch kit and Chain recommendations zcarter Yamaha Tech 9 22 Mar 2012 23:21

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 15:39.