Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > BMW Tech
BMW Tech BMW Tech Forum - For Questions specific and of interest to BMW riders only.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 2 Sep 2003
Steve Pickford's Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2003
Location: Oxford, UK
Posts: 994
Ticking top end

I've just re-built the top ends on my R80 GS Paralever. Everything de-coked, new valve springs, gaskets, o' rings and grommets & stainless push rod tubes. The bike starts and runs fine but there is a persistent ticking noise from both cylinder heads that increases in line with engine speed. The rocker gear is in good condition, everything was lubed on re-assembly and the valve clearances were set at Inlet 0.1mm & Exhaust 0.2mm as per the Haynes manual. I averaged 46.5mpg or 16.4kml on a 300mile trip a couple of days ago at 75-80mph mainly on motorways, so I do not feel that the problem is too serious.

Any ideas etc, all help appreciated.

Thanks

Steve
__________________
My photos: www.possu.smugmug.com
Reply With Quote
  #2  
Old 2 Sep 2003
Gold Member
Veteran HUBBer
 
Join Date: Mar 2001
Location: British Columbia
Posts: 246
Steve,

I have had the same problem with my G/S after and extensive re-fit. Apparently, the noise we are both hearing is a result of the rocker arm's not being properly shimmed. In talking with other owners, I was told by some the accepted method is to use a 'c' type clamp to pull the pillow blocks together prior to torqueing the heads down.
*A WORD OF WARNING*
I have not substantiated this with a BMW Mechanic, so I would talk to someone experienced with Airheads before doing this. According to my Haynes repair manual, this proceedure was only necessary with the older /5 series, and the newer bikes have 'self aligning' pillow blocks. It may be that shimming of the clearence is in order, to what clearence I don't know. I have discussed this with people that performed thet c clamp trick on newer bikes, but look into it further before you attempt this, as I will. I wouldn't want to be responsible for any damage due to false advise!

However, as to the cause of your noise, it does sound like this is it. As to damage caused by the gap in clearence, it is unlikely.
Reply With Quote
  #3  
Old 3 Sep 2003
Grant Johnson's Avatar
HU Founder
Veteran HUBBer
 
Join Date: Dec 1997
Location: BC Canada
Posts: 7,216
Correct rocker arm end play is .05mm +- .02mm. or between .03 - .07mm

If it's more it will make a racket that sounds like valves out of adjustment.

Shims are available from BMW dealers, in .20, .25, .30, .35 and .50 mm thicknesses. (Note: the accuracy of the shims from the factory is suspect, some are a little thicker some a little thinner, e.g. a .20 is actually .22, and some have a burr on the edge which should be sanded off.) The shim is on top of the rocker arm. Don't try to squeeze with a c-clamp, doesn't work on the later models.


------------------
Grant Johnson

Seek, and ye shall find.

------------------------

One world, Two wheels.
www.HorizonsUnlimited.com
__________________
Grant Johnson
Seek, and ye shall find.

------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
Reply With Quote
  #4  
Old 3 Sep 2003
Steve Pickford's Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2003
Location: Oxford, UK
Posts: 994
Slackened off the heads earlier & re-torqued them to 28ftlbs and re-set the valve clearances. Both left hand clearances were about 0.02mm loose and both right hand side clearances were tight by the same amount. Once re-assembled, the ticking was still present but slightly quieter.

Thanks for the advice on the rocker gear shimming, unfortunately I don't have time to do this at the moment but will report on the results when I do.

Thanks

Steve
__________________
My photos: www.possu.smugmug.com
Reply With Quote
  #5  
Old 3 Sep 2003
Contributing Member
Veteran HUBBer
 
Join Date: Nov 2000
Location: Wirral,UK
Posts: 172
Hi Grant

Interesting, I though that the clamp method worked OK on later models. There is some clearance in the rocker block stud holes on my '93 and I've certainly squeezed them together swith some degree of success. In fact, our local BMW dealer couldn't remember ever having sold any shims - but he probably can't remember selling an airhead either. Is it maybe a question of the amount of play that can be corrected? Alignment certainly isn't an issue on the later bikes.

Cheers

------------------
Sean
__________________
Sean
Reply With Quote
  #6  
Old 3 Sep 2003
Grant Johnson's Avatar
HU Founder
Veteran HUBBer
 
Join Date: Dec 1997
Location: BC Canada
Posts: 7,216
Problem with the squeeze method is getting the clearance right. On my own I found that squeeze only varied it by .01mm at best, (once tightened down) so pretty hopeless. Others may be different. Dealers don't sell shims cause they're too dumb fat and lazy to do it right, imho.

"They all do that sir" is the usual response to a complaint of valve noise.

Properly set up ones don't. Mine is remarkably quiet compared to almost all others I've heard except brand new ones, and mine still sounds new.

------------------
Grant Johnson

Seek, and ye shall find.

------------------------

One world, Two wheels.
www.HorizonsUnlimited.com
__________________
Grant Johnson
Seek, and ye shall find.

------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
Reply With Quote
  #7  
Old 4 Sep 2003
Steve Pickford's Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2003
Location: Oxford, UK
Posts: 994
Just ordered a selection of all size shims from Sherlocks. I've two GS Paralevers to do when I return from two weeks in Europe (we leave this Friday).

I've ordered 4 of each shim (£10.00) as I'd rather be able to measure the clearance and remedy the situation immediately rather than have to put the bike back together and then do it again after ordering the required shims.

Looking forwards to a quieter engine, will post results in a couple of weeks or so.

Steve
__________________
My photos: www.possu.smugmug.com
Reply With Quote
  #8  
Old 4 Sep 2003
Registered Users
HUBB regular
 
Join Date: Dec 2001
Posts: 71
Steve,
i agree with what has been said,
i did a similar rebuild.....i had to re shim the valves....not a big job...i agreewith grant re dealers....it isn't their bike ..it isn't their problem !!!
Reply With Quote
  #9  
Old 23 Oct 2003
Grant Johnson's Avatar
HU Founder
Veteran HUBBer
 
Join Date: Dec 1997
Location: BC Canada
Posts: 7,216
So what were your results Steve?

------------------
Grant Johnson

Seek, and ye shall find.

------------------------

One world, Two wheels.
www.HorizonsUnlimited.com
__________________
Grant Johnson
Seek, and ye shall find.

------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
Reply With Quote
  #10  
Old 23 Oct 2003
Steve Pickford's Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2003
Location: Oxford, UK
Posts: 994
Carried out the work last Sunday. Had the shims for a while but laziness had taken a hold on me.

All four rocker arms had clearances on the tight side. I expected the clearances to be loose, not tight?

Interestingly, all four arms had 2 x 0.3mm shims fitted. I expect that this is the standard BMW fitment upon leaving the factory? On both inlets I only had to remove one of the shims. On the exhausts, I removed both shims & replaced them with a 0.2mm shim in each arm.

The result is a quieter running engine, Worth doing, took about 2 hours in total, taking it easy. Easy to carry out as long as you have Verniers & a Micrometer. The shims are only 60p each from Sherlocks.

This bike is now for sale, see my posting in the relevant section, full spec on contacting me.

Steve
__________________
My photos: www.possu.smugmug.com
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 15:49.