Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > BMW Tech
BMW Tech BMW Tech Forum - For Questions specific and of interest to BMW riders only.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 21 Oct 2006
Registered Users
HUBB regular
 
Join Date: Jun 2006
Location: sydney
Posts: 38
why does driveshaft break?

Hi i have an 88 r100 gs, 80k, original driveshaft. I am repacing the Tranny.

Why does the driveshaft break?
Exactly, what breaks and how can you check for wear?
What can you do to avoid the problem?
Can you over grease u - joints?

Cheers
Reply With Quote
  #2  
Old 21 Oct 2006
Registered Users
Veteran HUBBer
 
Join Date: Sep 2003
Location: Estonia
Posts: 787
Why they brake down?

Well excuse me, but welcome to the Real World!

Everything that moves wears. They all brake down sooner or later but how soon mostly depends on the knob who holds the handlebars, how he loves-knows-ridestyles-and-maintains the bike he rides with.

120Ks on two boxers for me and exacly ZERO problems, if you ask from me.

Nevertheless I carry FD bearing repair kit with me, takes very little space and doesn't cost much at all, it's like a separate chain-set for me, but costs a lot less and a hell lot more hasslefree way powering the rear wheel.

Trannys on some airheads are bulky tho, you should always do your homework before heading out for the big trip. I think most of hardcore airhead travellers have their trannys modded (bearings?) before heading out.

Airhead experienced travellers will comment this in detail i hope!

Last edited by Margus; 21 Oct 2006 at 18:58.
Reply With Quote
  #3  
Old 21 Oct 2006
Dodger's Avatar
Large Golden Member
Veteran HUBBer
 
Join Date: Aug 2005
Location: BC, Canada
Posts: 1,085
Yes you can overgrease u joints .
I have found that the only type of grease that is any good for universal joints is synthetic , I use Metalon grease .It works very well in the extremes of temps we get in Canada .
Synthetic gear and final drive oil is good idea too .
__________________
Blessed are the cracked, for they let in the light. - Spike Milligan
"When you come to a fork in the road ,take it ! When you come to a spoon in the road ,take that also ."
Reply With Quote
  #4  
Old 21 Oct 2006
Redboots's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Feb 2006
Location: On the border - NE FR
Posts: 865
Unhappy Shafted

Quote:
Originally Posted by radioactiveangel
Hi i have an 88 r100 gs, 80k, original driveshaft. I am repacing the Tranny.
Why does the driveshaft break?
Exactly, what breaks and how can you check for wear?
What can you do to avoid the problem?
Can you over grease u - joints?
Hi Radioactiveangel

On the BM's its crap design.
On the paralever models there are 2 UJ's, one at either end.
This shaft on the road bikes (RS/RT) seems to be ok but the gs has much more suspension travel.
This can overwork or try to "block" the action of the UJ. There is also a rubber cush in the shaft that can cause a certain amount of whip.

There are 2 problems with this shaft:
No way to grease it without stripping it.
No circlips holding the bearing caps in place.

Various people re-work the shaft to include a grease nipple at each end and to add circlip grooves to retain the bearing caps.

The standard unit has "chisseled" notches to hold the caps in place. These can wear in time and allow the cap to come out and hit the shaft casing with predictable results.

You can also loose your grease from the uj if your gearbox seal leaks enough that it "washes" the grease away... also with predictable results.

Thats why I'm getting an exchange shaft from Erich Diamant before my big trip. €325 seems to be cheap insurance.

You cant overgrease the original uj. On the aftermarket ones, I suppose its possible, but the grease will just end up in the shaft housing.

If you strip you shaft down every 30k kms, re-grease and re-peen the endcaps, there would not be any problems... in theory.

Bests of luck
Redboots.

PS. Are you still looking for a gearbox? I only know of ones in Europe though.
__________________
Nostradamus Ate My Hamster
Reply With Quote
  #5  
Old 22 Oct 2006
Mr. Ron's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Oct 2003
Location: Vancouver, BC, for now...
Posts: 792
Talking

80k!! If this shaft is original, and your having this much trouble with your transmition, i would replace the shaft the same time you replace the new tranny. Your shaft may be okay, but the odds are against you at this point. Some people have gone over 100k with the stock shaft, but most haven't. This is a good opertunity to replace your shaft with a re-built shaft with greasable/replaceable u-joints and good rubber dampener. For the price, it's worth getting one of these. My shaft was replaced over 100k miles ago and is still in excellent shape, but i re-grease mine every 10k-15k miles. Maintinence is the key to longevity.
Make sure your rubber boots on either end of your swingarm are in good shape with no cracks. If they also have this mileage on them, they should be replaced, they are also cheap.
Whatever grease you use to lube your splines, make sure it is a moly grease. This prevents corrosion and sticks best to the metal.
Check out these links on grease and driveshafts:
http://www.advrider.com/forums/showt...ghlight=grease
http://www.advrider.com/forums/showt...ghlight=grease
http://www.advrider.com/forums/showt...ghlight=grease

...tons of info here. Also answers to all your questions
Reply With Quote
  #6  
Old 23 Oct 2006
Registered Users
HUBB regular
 
Join Date: Jun 2006
Location: sydney
Posts: 38
new driveshaft

Yes thankyou Margus, i am aware of the universal law of gradual decay i wasnt asking 'why' as in 'why does it break' perhaps i should of re phrasaed the question as ' how does it break'.

I now understand thanks for the other posts ADV riders posts very helpful, especially re: shaft drive phase. I am having mine replaced anyway but will look at the original to see if any lateral movement in shaft.

I will be installing the tranny and driveshaft in Pakistan. Could somebody clarify for me exactly what grease to look for and is their some helpful sites to show me exactly where and how much.

Thanks.

Very much in the deep end.
Reply With Quote
  #7  
Old 23 Oct 2006
Registered Users
HUBB regular
 
Join Date: May 2006
Location: Costa Rica
Posts: 36
Quote:
Originally Posted by radioactiveangel
Yes thankyou Margus, i am aware of the universal law of gradual decay i wasnt asking 'why' as in 'why does it break' perhaps i should of re phrasaed the question as ' how does it break'.

I now understand thanks for the other posts ADV riders posts very helpful, especially re: shaft drive phase. I am having mine replaced anyway but will look at the original to see if any lateral movement in shaft.

I will be installing the tranny and driveshaft in Pakistan. Could somebody clarify for me exactly what grease to look for and is their some helpful sites to show me exactly where and how much.

Thanks.

Very much in the deep end.
The U-joints fail because eventually, the grease gets out past the seals and they run dry.
My experience with them, mostly street driven GS's, is that the rubber damper twists as a result of a failing U-joint binding up, not the other way around.
I rebuild my own using U-joints from a Toyota Dyna delivery truck stearing shaft. About $40 in parts.
Briefly, I burn out the old U-joints with a cutting torch and then Dremmel out the swedge marks. Then install the new joints and tack-weld washers over the end caps to hold them in place.
Details can be found at www.advriders.com. Search, "Proactive Driveshaft Repair".
__________________
Motomech
Playas del Coco
Costa Rica

"..an attaching bike on which one rolls serenly along."
(Google translation of a French R100GS review)
Reply With Quote
  #8  
Old 28 Oct 2006
Mr. Ron's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Oct 2003
Location: Vancouver, BC, for now...
Posts: 792
Talking

Quote:
Originally Posted by radioactiveangel


I will be installing the tranny and driveshaft in Pakistan. Could somebody clarify for me exactly what grease to look for and is their some helpful sites to show me exactly where and how much.

Thanks.

Very much in the deep end.
I found this for you: http://www.airheads.org/content/view/226/98/
Look through the site to answer all your questions
Reply With Quote
  #9  
Old 28 Oct 2006
Registered Users
Veteran HUBBer
 
Join Date: Oct 2005
Location: Norwich,Ontario,Canada
Posts: 1,051
driveshaft breaks

Concur with Redboots opinion ,the design on the older paralever is flawed and it is also evident on the street models. I have experienced three such failures on a 1994 R100R , always the aft u-joint seizing up and destroying itself. The original shaft lasted 163000km and I was willing to allow it as being used up. However its replacement went a few years later at 75000km and then that one lasted barely a year before it crapped out at 27000km. This last one was the worst as it happened half-way down Baja and entailed hitching a ride back to San Diego with the bike to get it repaired .All work was done by factory trained technicians at modern well equiped BMW dealers, so it is not a question of hamfisted installations.
My theory is that one of the causes may be the aging grease . The model has been discontinued since '94 or so, and I assume that all replacement shafts were manufactured before that in one production run, including all its flaws( non- greasable ,too wimpy, too sharp angles of power input) Since then the tiny bit of grease has been decaying, using up its "half lives" so to speak, judging from the decreasing distances between replacements.
It gets very annoying paying $600US for what is basically a grease job.Fortunately at least the last one was covered by BMW's one year waranty on parts.
Here in Otario there is a machine shop in Kitchener who specialise in repairing driveshafts on BMW and all kinds of motorcycles and cars and I hear good reports about their work. See them at www.brunos.us
__________________
http://advrider.com/index.php?thread....207964/page-5 then scroll down to post #93
Reply With Quote
  #10  
Old 29 Oct 2006
Dodger's Avatar
Large Golden Member
Veteran HUBBer
 
Join Date: Aug 2005
Location: BC, Canada
Posts: 1,085
u joints

I have gained a lot of experience with U joints on machinery over the years and have a pet theory regarding greasing .
They never wear out evenly ,usually one side or sometimes both sides of the "spider" will fail before the other , but never all 4 together .
The cups contain roller brearings ,which by their nature ,require very little lubrication , so why does one side fail before the others ?
Very often there will be rust present .

Also Sjeord comments upon the short life expectancy of the replacement units .

I think that it has more to do with the integrity of the grease seal on the bearing cup .When the rubber seal begins to fail it allows moisture to be drawn into the u joint .[It may only be a very small amount of moist air being sucked into a warm u joint as it cools down after a long ride ] But over a period of time there is sufficient water to degrade the grease in the cup and the bearing fails.
Seals can fail through old age and the effects of ozone and UV light .

The out of phase condition I personally believe is due to the u joint failure and not vice versa .

Consequently I would always grease the u joints sparingly at a regular interval [based on the useage of the bike] and always before storing the bike for any length of time .In order to do this a grease nipple is necessary ,which would require a modification .This mod impressed me :


I believe this type of mod ,other than the urethane damper , could be done by a competent machine shop anywhere if you had the correct parts to hand .
If I was going RTW ,I would have my driveshaft modified in this way and lubed with synthetic grease .


Best of luck .
Dodger
__________________
Blessed are the cracked, for they let in the light. - Spike Milligan
"When you come to a fork in the road ,take it ! When you come to a spoon in the road ,take that also ."
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Need driveshaft boot for G/S in Pakistan Mombassa BMW Tech 4 29 Aug 2006 19:29
Khyam wind break kevinrbeech Equipment Reviews 0 7 Nov 2005 00:20
Khyam wind break kevinrbeech Camping Equipment and all Clothing 0 3 Nov 2005 01:23
speedometer break down XL650 fireboomer Honda Tech 2 7 Sep 2004 13:32
starting problems/disk break upgrade andreasb BMW Tech 8 1 Dec 2002 23:43

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 14:53.