Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > BMW Tech
BMW Tech BMW Tech Forum - For Questions specific and of interest to BMW riders only.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 29 Apr 2006
Contributing Member
Veteran HUBBer
 
Join Date: Feb 2004
Location: St Andrews
Posts: 662
Question Back up fuel pump for R1200GS

Hi People, before I show up my ignorance of things mechanical in front of BMW trained mechanics, does anyone know if the fitting of a back up fuel pump and a selector switch either mechanical or pressure initiated in the event of a primary pump failure is a feasable proposition. The reason for the question is that I had a failure 2 months ago and whilst not in the wilds of South Africa, in a fairly remote part and it took 3 days and US$750 to get it to a dealers on the outskirts of Durban. A back up pump would have allowed me to keep my coupens and use them for the purpose for which they were printed. Ride safe, Mike Anderson
__________________
Mike
---------
Mike is riding the twisty road in the sky
Reply With Quote
  #2  
Old 29 Apr 2006
Gold Member
HUBB regular
 
Join Date: Jan 2006
Location: Belgium
Posts: 27
Hi Mark,

on most today's (gas) indirect fuel injection, and that's the case on the GS12, the pump is part of the injection system. Its pumps fuel under a certain pressure up to the injectors placed in the inlet pipes. Those injectors are regulated by the inboard computer. So, I am quuite sure a "simple" backup pump (eg. an electrical fuel pump to feed a carb, you can buy any place) could not do the job, but I will check it out.
And next time have coupons with with longer delays when driving a BM out there...

Norbert
PS: I just have taken delivery of my 12GSA, and BMW added free a full assistance (incl replacement car), for whole Europe, as long as I ahve this bike ... but not in Afrika, only SA
Reply With Quote
  #3  
Old 1 May 2006
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2002
Location: Sydney, NSW, Australia
Posts: 1,362
Quote:
Originally Posted by norbert and francoise
So, I am quuite sure a "simple" backup pump (eg. an electrical fuel pump to feed a carb, you can buy any place) could not do the job, but I will check it out.
No. A carb pup is low pressure.

EFI requires about 30psi and 1 to 2 litres per minute flow rate.

But you could source a pump from an EFI car/truck/4WD and use that to get you home. Would cost around $300aud (new pump here)?

On the 'failed' pump ... try reversing the electrical supply to the pump motor it self .. sometimes the pump grinds to a halt on junk in the fuel - by running it backwards you can get the junk out and get the pump working again. Note - CAN buss on the newer 12 should be removed when doing this - otherwise you'll probably blow that up too.

It is not unknown for the wires leading through the tank to go open circuit either.


I'm not taking a spare fuel pump on my trip. Weight + size vs failure rate = no take.
__________________
---
Regards Frank Warner
motorcycles BMW R80 G/S 1981, BMW K11LT 1993, BMW K75 G/S
Reply With Quote
  #4  
Old 1 May 2006
Gold Member
HUBB regular
 
Join Date: Jan 2006
Location: Belgium
Posts: 27
thanks Frank for your precise answer,
I checked out, and confirm: EFI requires about 2,5 bar.

Norbert
Reply With Quote
  #5  
Old 1 Feb 2011
Contributing Member
Veteran HUBBer
 
Join Date: Feb 2004
Location: St Andrews
Posts: 662
Guess who is presently stuck in Lusaka having wasted lots more coupons again with his 3rd fuel pump/unit failure, who says lightening never strikes twice/thrice? By the way the Lusaka BMW agent really is a complete and utter tosser but hopefully the guys in Windhoek are trying to help me out. Ride safe.
__________________
Mike
---------
Mike is riding the twisty road in the sky
Reply With Quote
  #6  
Old 1 Feb 2011
T.REX63's Avatar
Gold Member
Veteran HUBBer
 
Join Date: Mar 2010
Location: Atlanta, GA / USA
Posts: 295
Quote:
Originally Posted by maja View Post
... The reason for the question is that I had a failure 2 months ago
...
What year 1200GS are you referring to?
__________________
Thomas

"Hey, ...I'm just ridin' shotgun"
Reply With Quote
  #7  
Old 2 Feb 2011
Registered Users
Veteran HUBBer
 
Join Date: Jul 2008
Location: Aussie expat in Switzerland half way RTW
Posts: 611
Cool fellow GS'er

Very interested in this thread. Following progress intently.
__________________
TurboCharger + Francois (our BMW R1200gs) '07
www.riding2up.net, blog.riding2up.net
Reply With Quote
  #8  
Old 2 Feb 2011
Registered Users
Veteran HUBBer
 
Join Date: Feb 2008
Location: Washington, DC
Posts: 1,377
is a problem with the fuel pump, or fuel pump controller? FPC failures are pretty common, fuel pumps not so much. FPCs are very small and cheap and definitely worth bringing a spare with!
Reply With Quote
  #9  
Old 4 Feb 2011
Registered Users
Veteran HUBBer
 
Join Date: Jul 2008
Location: Aussie expat in Switzerland half way RTW
Posts: 611
Fuel pump controller bypass

Quote:
Originally Posted by motoreiter View Post
is a problem with the fuel pump, or fuel pump controller? FPC failures are pretty common, fuel pumps not so much. FPCs are very small and cheap and definitely worth bringing a spare with!

Better still and much much cheaper than a spare FPC is this bypass cable. Wish I had one with me when my FPC died in Turkey!

BurnsMoto - BMW Motorcycle Fuel Pump Bypass Cable
__________________
TurboCharger + Francois (our BMW R1200gs) '07
www.riding2up.net, blog.riding2up.net
Reply With Quote
  #10  
Old 4 Feb 2011
Contributing Member
Veteran HUBBer
 
Join Date: Feb 2004
Location: St Andrews
Posts: 662
Hi People, back on the road again thanks to Andy W's great blog on Fuel Pump Bypass and from now on I will never travel without it. Couple of points before the nitty gritty bit, I have had 2 controller failures, 1 pump and 1 pump unit which started disintegrating before my very eyes and this was quickly followed by the unit on the opposite side which receives the unneeded output from the fuel pump also cracking up which seems to have been the result of using ethanol biogas additive type fuel in a European spec fuel system which you have to do in most if not all of the US. Whatever caused it it has cost me lots of coupons and that hurts. The Nitty Gritty then my bike is a 2004 r1200gs and only the gs's are affected by the controller failures due to moisture getting under the silicon filling of the unit due to the crap design and positioning of the control unit, other types of 1200's rest easy. When I stripped mine down as per the blog to make a bypass the short on the circuit board which up to that point appeared to have been fully protected was revealed. The article explains the need for a control which appears to have started with the 1200 series and been previously thought unnecessary. go to

Motorcycle Info Pages - Home and click on Fuel Pump Controller bypass, I would suggest that you read the addition to the article which suggests a variation which may be a better system but as is pointed out takes up more space. So now you know, never leave home without one. from a very wet Victoria Falls where the spray chases away the rain, ride safe.
__________________
Mike
---------
Mike is riding the twisty road in the sky

Last edited by maja; 4 Feb 2011 at 13:03. Reason: missed a bit
Reply With Quote
  #11  
Old 6 Mar 2011
Registered Users
New on the HUBB
 
Join Date: Jan 2009
Posts: 14
Simple fix I will try and get photos of the next 1200 I do this too

The black vented fuel pump housing cover (left top side of fuel tank remove the alloy side cover to acces it ) remove it and cut rubber (inner tube or coke bottle flattened out or a side of a plastic "gallon" oil container) a little bigger than the vents and use a good silicone sealer and "glue" the rubber to the plastic BUT leaving an area open but covered(to prevent water access) at the lower side to allow air circulation

Set that to the side and remove the fuel pump controller N.B. Do not pull the cables remove them before you unscrew the torx and if there is any water down in the well dry it out with an airline

carefully lift up the controller and you will see a couple of cables going to a blue plug
This is the actual pump power connection the bits above are only the power connection and CANBUS wire it's that small alloy thing that tells the pump when to power up

There is a seal around the edge remove it clean it and its contact area for any grit or dirt on the bike and the controller if there is any water down in that part dry it out with an airline too

Now the easy part Get Vaseline or any good qaulity petroleum jelly and cover the blue plug and the seal and the contact faces and refit the controller Again smear vaseline onto the pump connections and level sensor connections

At this stage I usually paint the pump controller with a product called Waxoyl it's a black underbody wax / sealant for cars I guess maybe wet chain grease would do but I've never used it

Refit the connections and the covers and Robert would be your fathers brother, Be careful when fitting the out alloy cover the clearance are very fine so I usually fold the rubber flap/cover down as I set it on, so that here is not a gap for water to get below

I've 2 friends with a 2004 and a 2005 still on the original controllers with just my modification
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
3ja fuel pump removal braindead Yamaha Tech 4 10 Jan 2005 19:51
Africa Twin Fuel Pump mattpope Honda Tech 4 12 Sep 2004 02:10
Dakar Fuel Pump and Frame Bolts hunternielson BMW Tech 4 20 Aug 2004 08:48
Africa Twin Fuel Pump Dodgy Dave Honda Tech 13 7 Jan 2004 03:03
KM per Liter for XT 600 Z Fuchur Yamaha Tech 4 10 Apr 2002 04:45

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 15:49.