Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > BMW Tech
BMW Tech BMW Tech Forum - For Questions specific and of interest to BMW riders only.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 9 Jun 2004
Registered Users
HUBB regular
 
Join Date: Dec 2002
Location: Zambia
Posts: 45
Play in Driveshaft on F650

Hi all,

I'm on the road, in Southern Tanzania, (just put the bike on a motorboat across the Rivuma River a few hours ago) on a long ride, and am experiencing a curious clunking sound coming from the area near my right ankle.

I found that the 32mm nut holding my sprocket on was loose not long ago...much to my dislike...and after tightening it I found that the clunking noise stopped. Then later, it started again, only this time the nut doesn't seem to be loose (at least I can't move it with my fingers this time) and I've noticed there is in-out play in the shaft the sprocket attaches to...

So, what's the clunking? Is there supposed to be play in the shaft (not more than a mm, very similar to the in-out play on the gear shift pedal...)?

I'll be around town fixing broken welds for a day or so.

Help!

Cheers,
Hunter
__________________
Hunter
Reply With Quote
  #2  
Old 10 Jun 2004
Grant Johnson's Avatar
HU Founder
Veteran HUBBer
 
Join Date: Dec 1997
Location: BC Canada
Posts: 7,216
I suspect the sprocket is moving, the same as before, just the nut isn't as loose. It is supposed to be REALLY tight. A two foot breaker bar, big stomp on the brake pedal, and tighten as tight as you can. On most bikes there is a flat washer under the nut which you can bend over to lock the nut in place, dunno about the F650.

A small amount of endplay is ok.

------------------
Grant Johnson

Seek, and ye shall find.

------------------------

One world, Two wheels.
www.HorizonsUnlimited.com
__________________
Grant Johnson
Seek, and ye shall find.

------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
Reply With Quote
  #3  
Old 10 Jun 2004
Registered Users
HUBB regular
 
Join Date: Dec 2002
Location: Zambia
Posts: 45
Thanks Grant,

I'll get a wrench and an elephant to step on it today...and if I can find some blue loctite in Mtwara, I'll whack that in there too (would super glue work?).

It's good to know the play is normal, but I'm still fretting about the kalunk kalunk kalunk sound I'm getting pulling up hills at low revs.

More later.
__________________
Hunter
Reply With Quote
  #4  
Old 10 Jun 2004
jim jim is offline
Gold Member
Veteran HUBBer
 
Join Date: Aug 2003
Location: Cape Town South Africa
Posts: 222
hey hunter

If you cant find loctite try some nail varnish, not ideal, but it works OK. Of course its important to choose a colour that accentuates your eyes...

I leave Mbeya today, dont know where Mtwara is... maybe nearby? I might even see you there. Ive got loctite with me.

Jim
__________________
"If we don't find something good at least we will find something new." Voltaire
Reply With Quote
  #5  
Old 11 Jun 2004
Grant Johnson's Avatar
HU Founder
Veteran HUBBer
 
Join Date: Dec 1997
Location: BC Canada
Posts: 7,216
Hmmm, don't like the sound of the kalun kalunk...

COULD be one of several things -

1. the sprocket splines are stripped and under high load it jumps

2. chain and sprockets totally worn out/loose, same thing

3. gearbox/primary system problems

1 and 2 are most likely.

See if you can get together with Jim, should be able to work it out together.



------------------
Grant Johnson

Seek, and ye shall find.

------------------------

One world, Two wheels.
www.HorizonsUnlimited.com
__________________
Grant Johnson
Seek, and ye shall find.

------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
Reply With Quote
  #6  
Old 11 Jun 2004
Registered Users
HUBB regular
 
Join Date: Dec 2002
Location: Zambia
Posts: 45
Well, it seems there was a bit of many things at play...

I found a local Vocational Training College (called VETA, for any other travellers going to Mtwara, TZ in the far south East of the country) and while the welders and metal benders were fixing a very badly mangled headlight assembly from a little spill I took, (damn sandy Mozambiquan roads anyhow) I went to the mechanic's shop and tried to loosen the big nut. No doing. It was tight as can be. But, on Jim's advice via email, I checked the rear wheel, and very carefully adjusted the chain...then lubed it.

Presto. No more Kalun Kalunking...for now.

I'll keep monitoring the situation though, because I think I hear something now and then...not kalunk, but something under strain.

The sprockets look good, and the chain isn't bad either...though I don't claim to say I've adjusted the tension correctly...so it could be a combo of all these.

Thanks guys,
Hunter
__________________
Hunter
Reply With Quote
  #7  
Old 12 Jun 2004
Grant Johnson's Avatar
HU Founder
Veteran HUBBer
 
Join Date: Dec 1997
Location: BC Canada
Posts: 7,216
Hunter,

see an article I wrote years ago on chain adjustment when I was writing for Cycle Canada. It's now listed on the tech pages: http://www.horizonsunlimited.com/tech/

Should give you all you need to know to be sure it's right.

------------------
Grant Johnson

Seek, and ye shall find.

------------------------

One world, Two wheels.
www.HorizonsUnlimited.com
__________________
Grant Johnson
Seek, and ye shall find.

------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
Reply With Quote
  #8  
Old 14 Jun 2004
richardb's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Mar 2003
Location: guildford, surrey, UK
Posts: 138
I had a similar experience not long ago on my Dakar. Chain tighteing and lube worked temporarily, but I think it was down to the chain being unevenly stretched. The noise kept coming back after a couple of days. I rode it for a fair distance like that, from Ushuaia northwards, but in the end had chain and both sprockets replaced in Sao Paulo Brazil. As they had lasted me from Los Angeles I was reasonably happy about that. The problem disappeared and has not returned.

Richard

------------------
Richb
http://www.postmaster.co.uk/~richardbeaumont/60684/
Reply With Quote
  #9  
Old 23 Jun 2004
Registered Users
HUBB regular
 
Join Date: Dec 2002
Location: Zambia
Posts: 45
Richard,

I've determined you're right. I think the chain has seen the end of it's lifespan. I should have known it wouldn't make it all the way to Nairobi in good shape...but it will make it all the way!

I don't have a choice, so I'm pushing ahead. Slowly as she goes, a little lube every 100km or so...everybody think good thoughts!

Hunter
__________________
Hunter
Reply With Quote
  #10  
Old 1 Jul 2004
Chris Scott's Avatar
Super Moderator
Veteran HUBBer
 
Join Date: Jun 2000
Posts: 4,801
Glad the noises have gone and hope they will stay gone.
One thing I found in the desert (on XTs this was, not on BMs) was check/adjust your chain tension in the morning when its cold - by the evening it would look alarmingly slack but would tighten up overnight.
I presume its hot in Kenya right now

Chris S

(FWIW, you cant beat an X-ring DID)

------------------
Author of Sahara Overland and the Adventure Motorcycling Handbook, among other things

http://www.sahara-overland.com and http://www.adventure-motorcycling.com
Reply With Quote
  #11  
Old 3 Jul 2004
Registered Users
HUBB regular
 
Join Date: Dec 2002
Location: Zambia
Posts: 45
Thanks Chris, everyone,

I made it to Nairobi! Two of the collars that protect the pins on the chain had broken away, and the stretch in the chain was obvious. I found a guy here who repairs older BMWs, and will be replacing my chain with a new one soon. I guess I'll just flip the sprockets though, they both look fairly good.

Now, with the new chain, I'll be proceeding directly into the rocky, sandy, dusty north. This is where I get confused by the number of opinions on chain lube, ranging from using nothing at all, to engine oil, to light 6 in 1, to chain wax. Last time, I tried the no-oil solution, then switched to 6 in 1 when the clunking started...maybe that explains the of the state of the chain.

I'm sure this thread exists somewhere else, I've probably read it...but I haven't found consensus, so I'm just making best guesses as I go.

Hunter
__________________
Hunter
Reply With Quote
  #12  
Old 4 Jul 2004
Mr. Ron's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Oct 2003
Location: Vancouver, BC, for now...
Posts: 792
Hello.
Try this link Motorcycle Chains

This should tell you all you need to know, if not more!
Reply With Quote
  #13  
Old 4 Jul 2004
Mr. Ron's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Oct 2003
Location: Vancouver, BC, for now...
Posts: 792
Hello
OOPS! That didn't work. Just do a hubb search for chain, your first hit is a good one!
Reply With Quote
  #14  
Old 4 Jul 2004
Grant Johnson's Avatar
HU Founder
Veteran HUBBer
 
Join Date: Dec 1997
Location: BC Canada
Posts: 7,216
Re sprockets, I don't recommend flipping. If there is any sign of hooking, it's best to replace.

In other words, if the teeth aren't prefectly symmetrical, replace. If the teeth are hooked, the effective tooth-to-tooth distance increases at a point in the rotation of the wheel, greatly increasing the stress on the chain and increasing the wear rate. So a new chain on old worn sprockets lasts e.g. half as long as with new sprockets.

------------------
Grant Johnson

Seek, and ye shall find.

------------------------

One world, Two wheels.
www.HorizonsUnlimited.com
__________________
Grant Johnson
Seek, and ye shall find.

------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
Reply With Quote
  #15  
Old 5 Jul 2004
Registered Users
HUBB regular
 
Join Date: Feb 2003
Location: Lubumbashi, DRC
Posts: 78
I did a lot of sandy, dusty, rocky roads in West Africa with my 650 (standard version), and experienced lots of problems with my chain. I also tried various options, and the best solution I found was when using no oil or anything for the chain.

jef
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 08:08.