Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > BMW Tech
BMW Tech BMW Tech Forum - For Questions specific and of interest to BMW riders only.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 18 Mar 2006
Registered Users
HUBB regular
 
Join Date: Aug 2003
Location: Norway
Posts: 47
R80GS; which problems to expect?

Hello all,
going from Norway to Oz in 2007. My bike has approx. 60k kms on the clock.
I bought the bike a couple of years back and I did the following:

1. New Valeo starter.
2. Gearbox; turned a Seeger ring groove in the shaft (can`t remember which) and changed all bearings. When the box breaks down, what is it that actually goes wrong?
3. Register chain and damper/slider.
4. Swingarm bearings.

Next on the list is a new driveshaft, although the one I have is OK.
Then new shock absorber.
I have an extra diodeboard and regulator to take along.
I`ll take the engine to bits and put in new valves and cut the seats (+ other stuff if necessary).

So what did I overlook? Any other bits that require attention?

regards

John

Reply With Quote
  #2  
Old 18 Mar 2006
Registered Users
New on the HUBB
 
Join Date: Dec 2004
Location: Lancashire, UK
Posts: 12
For the relatively small cost involved it may be worth replacing the valves and springs. I have heard that they may be a weakness in high mileage air cooled boxers. Perhaps the timing chain and tensioner as well, and take a spare starter relay. Good Luck with the trip.
Reply With Quote
  #3  
Old 19 Mar 2006
Registered Users
HUBB regular
 
Join Date: Oct 2003
Location: Norway
Posts: 70
Heisann.

The rotor is a common part that fails after some miles, and if you dont know how your carbs is, get then redone and tuned. This can save you some fuel on a long tripp...

God tur
yngve
Reply With Quote
  #4  
Old 19 Mar 2006
Gold Member
Veteran HUBBer
 
Join Date: Mar 2001
Location: British Columbia
Posts: 246
If you haven't already, take a look over the previous posts - there is lots of good discussion on preparing these bikes for a long trip.

I'd recommend changing the rotor for a solid one-piece rotor (see links for Motorade elektric), and use your existing rotor as a spare.
Brake pads and caliper rebuild.
FULL service.
I'd upgrade to progressive springs in the fork, as well as changing the shock.
New battery?
Add some full wrap 'bark buster' hand/ lever guards.
Make sure you take your bike for good a run down trip after all modifications/ fixes are performed to make sure everything works as you expect.

Enjoy!
Reply With Quote
  #5  
Old 20 Mar 2006
Contributing Member
Veteran HUBBer
 
Join Date: Jul 2002
Location: Sydney, NSW, Australia
Posts: 1,362
Take a alternator rotor, they fail more frequently that diode boards or regulators.

Fit a new hall effect sensor. Fit new spark plug caps (5k ohm types) and new spark plug leads (wire type).

I'd take a clutch cable too.
__________________
---
Regards Frank Warner
motorcycles BMW R80 G/S 1981, BMW K11LT 1993, BMW K75 G/S
Reply With Quote
  #6  
Old 20 Mar 2006
Registered Users
Veteran HUBBer
 
Join Date: Aug 2001
Location: Vancouver, BC - now at large in the world
Posts: 411
Timo, the Motorrad rotor is not "solid". It's still a wound rotor. The solid rotor setup is from http://euromotoelectrics.com/

------------------
Kevin

http://www.nohorizons.net
__________________
http://www.nohorizons.net
Reply With Quote
  #7  
Old 20 Mar 2006
simmo's Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Nov 2002
Location: melbourne
Posts: 555
Hi John

Make up a travellers gearbox output shaft flange puller and take some of the single use only driveshaft bolts that attach to the flange, you'll need them when you put the gearbox back in! Basically a circular peice of aluminium with a centre bolt to screw down on to the output shaft and four outer bolts to secure it to the flange.

Take a selector return spring and a spare outputshaft oil seal, not to mention the large output shaft bearing, it was hard to find, you will also want a spare gasket for the g/box lid.

Have a lightweight exhaust tool made with a cut out to use as a brace when doing the output shaft flange bolt up to its required zillion pounds of torque

Take spare instrument bulbs, I dont know if yours is the same as the earlier G/S but the charge circuit runs through the generator light bulb on the dash!!! You might only notice when your battery is flat and you think.bugger that bloody light didn't come on 500kms ago when I started it up.....

Harden the valve seats so you dont get valve recession on poor fuel. Put a braided front brake hose on.

Get a cheap rebuildable shock, such as an IKON, Ohlins is total overkill on such a evil handling slug.

If this is a paralever and you are carrying alot of weight, make sure you have a solution to the lower shock mount ripping out from the final drive housing.

Take a tyre repair system, tubes or plugs or whatever and know how to use it.

But when it all stops functioning as mine did for the umpteenth time yesterday at kilometere 900 of a desired 1050, remember that the footpegs on an 84 R80 GS are the same as on a 04 12GS.

At least it wasn't the bloody gearbox again. Thats progress I suppose.

alec


__________________
Close to Antarctica and a long way from reality
Reply With Quote
  #8  
Old 21 Mar 2006
Lifetime Member
Veteran HUBBer
 
Join Date: Oct 2000
Location: Nottingham England
Posts: 152
I agree with all the above advice and modifications - I have over 150,000 miles on my own G/S and some of the above modifications, but I ask you to bear in mind the bike has no idea where it is (eg. darkest India)... at the very MOST you wont do 50,000 kms to OZ, do you really think all the above is nessesary, worth the time and expense for less than 50,000kms?

If you didn't buy all the above you could quit work 6 months earlier !
I think you'll end up a mobile bike garage, carrying too much weight, having no space on the bike, and the hassle of looking after all the spares - security - not free enough to enjoy all parts of the trip.

Not for me I'm more from the minimalist school and sooner spend the money on petrol - travelling light.

Cables,bulbs etc.

New rotor, new shock, new driveshaft. Full service. Finish.

Oh and if you have room, a detense spring for the gearbox...
Reply With Quote
  #9  
Old 21 Mar 2006
Gold Member
Veteran HUBBer
 
Join Date: Mar 2001
Location: British Columbia
Posts: 246
It's a good point... How prepared is enough? Lot's of people have purchased a new enduro of some description and hit the road to glory. However, I think that most would suggest some form of preparation, especially on a 11-17 year old bike with 'known issues'.

Some of my most treasured adventures have been the cause of a breakdown of some sort, but I'd still rather fix what I can up front and at home in my garage - it will still break down when you least expect it!

I'm less sure about the arsenal of spare parts. It seems to me this should be somewhat variable to the availability of parts and/ or mail service where you are going.
Reply With Quote
  #10  
Old 25 Mar 2006
simmo's Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Nov 2002
Location: melbourne
Posts: 555
Some have scoffed at the generator light bulb being a culprit in the flat battery syndrome, others have suggested that as the light goes out when revs increase..assuming all normal..I must be delusional. Others say that it is outrageous to expect the whole charging system to be dependant on one small dash bulb. What stupid company would do that to its bikes...

Well sceptics its true. Although you wont find reference to it in your haynes or clymers, the genereator bulb acts as the exciter for the alternator. This means that the battery will not charge if the filament is broken.

Above 4000rpm the alternator will self excite and the battery will charge, but as you can imagine keeping a BM flat twin above 4000 is not how its ridden generally.

Thanks to BM cycles in Melbourne for the explanation, although it still feels like gobledy gook to me.

Maybe Frank can explain it!

__________________
Close to Antarctica and a long way from reality
Reply With Quote
  #11  
Old 25 Mar 2006
chris's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Jun 2000
Location: GOC
Posts: 3,326
Check: http://www.horizonsunlimited.com/ubb...ML/000074.html

I now own 3 bikes: A Triumph, a Honda and a Kawasaki.

Having an airhead Beemer is a good way of meeting people, particularly mechanics. If you do search out a mechanic, make sure he's not a BMW mechanic. In my experience they are overpriced/unskilled/dangerous. Jap/no-brand boys were much better.

HTH
ChrisB

------------------
TheBrightStuffDotCom
Reply With Quote
  #12  
Old 25 Mar 2006
Gold Member
Veteran HUBBer
 
Join Date: Mar 2001
Location: British Columbia
Posts: 246
The generator light/ charging system is indeed a funky way of running the charging system. Keep in mind that these bikes where designed back in the 60's, when this technology was more appropriate. What is amazing is that a bike so dated remains a viable option for world travel. I challenge you to go RTW on an early 70's Harley/ Ducati or Honda without similar issues. Of course, why didn't BMW update the bike? Well, as Beemer lore would have it, the K series was supposed to replace the boxers in the mid eighties, but continued popularity of the design and luke warm acceptance of the K bikes led to the boxers being held over until a real replacement could be manufacturer - the Oilheads. BMW did/ does not have a lightning fast development program....

Aside from the design of the charging system which would be expensive and difficult to change, the main problem with this setup is it's dependence on a notoriously weak filament type bulb. You can swap this out for a LED bulb - much more durable. Touratech:

http://www.touratech.de/shop_uk/enter.html

Offers and STD control lamp that replaces all the warning lights with a LED array. It requires a resistor to run the charging system. It is designed for plug in on the R80/100 GS but fitment on a G/S is possible with a bit more cutting and manual wiring.
Reply With Quote
  #13  
Old 26 Mar 2006
beddhist's Avatar
Contributing Member
Veteran HUBBer
 
Join Date: Sep 2003
Location: Whangarei, NZ
Posts: 2,214
First, this charging system setup is, or at least was at the time, standard car technology. Dto. for the starter motor. Even the alternator is half a car item.

According to the German Boxer Forum you can put a small resistor in parallel to the bulb. That way the current keeps flowing even if the bulb is dead.
__________________
Cheers,
Peter.

Europe to NZ 2006-10
Reply With Quote
  #14  
Old 26 Mar 2006
Atwoke's Avatar
Registered Users
Veteran HUBBer
 
Join Date: May 2005
Location: Northumberland, UK
Posts: 219
A truly interesting issue for loads of people...have to check what's in my bike..

Chris, looking forward to discussions in the North ...
__________________
You can never have too many bikes......

BMW R100GS
Triumph Tiger 885
Yamaha XT600e

Jens is gone, but not forgotten.
Reply With Quote
  #15  
Old 26 Mar 2006
Grant Johnson's Avatar
HU Founder
Veteran HUBBer
 
Join Date: Dec 1997
Location: BC Canada
Posts: 7,216
Quote:
Originally posted by beddhist:
First, this charging system setup is, or at least was at the time, standard car technology. Dto. for the starter motor. Even the alternator is half a car item.
Agreed, common - and I've seen even dumber - like the taillight that was doing the job of the charge bulb on the BMW, and if it blew there was a switch to flick, so you could continue on - Ducati, 1964. I just rode mine with the switch always flicked, cause the taillight burned out regularly! didn't seem to make any difference...

Quote:
Originally posted by beddhist:

According to the German Boxer Forum you can put a small resistor in parallel to the bulb. That way the current keeps flowing even if the bulb is dead.
Sounds like a good one to translate and post here Beddhist! Thanks!

Don't you just love getting volunteered?


------------------
Grant Johnson

Seek, and ye shall find.

------------------------

One world, Two wheels.
www.HorizonsUnlimited.com
__________________
Grant Johnson
Seek, and ye shall find.

------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 02:44.