Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > BMW Tech
brake cam o-rings brake cam o-rings
Register FAQ Calendar Today's Posts
BMW Tech BMW Tech Forum - For Questions specific and of interest to BMW riders only.
Photo by Ellen Delis, Lagunas Ojos del Campo, Antofalla, Catamarca

I haven't been everywhere...
but it's on my list!


Photo by Ellen Delis,
Lagunas Ojos del Campo,
Antofalla, Catamarca



Reply
Page 1 of 2 1 2
 
LinkBack Thread Tools Display Modes
  #1  
Old 22 Jan 2005
Registered Users
New on the HUBB
  
Join Date: Apr 2002
Location: adelaide australia
Posts: 6
brake cam o-rings
I have an 82 G/S, recently oil has been leaking
on to the rear brake pads via the brake cam,I
have removed the brake cam and it only has two
o-rings on it, but six grooves on the cam.A friend told me it should have four o-rings,if so which grooves should I use for the o-rings.

Thanks.
Reply With Quote
  #2  
Old 23 Jan 2005
Grant Johnson's Avatar
HU Founder
Veteran HUBBer
  
Join Date: Dec 1997
Location: BC Canada
Posts: 7,226
As many as you can get in...

And grease well.

and don't forget to renew the felt on the outside as well.
__________________
Grant Johnson
Seek, and ye shall find.
------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
Reply With Quote
  #3  
Old 25 Jan 2005
Contributing Member
Veteran HUBBer
  
Join Date: Aug 2001
Location: B.C. Canada
Posts: 209
I should have known to ask here first. Just posted on UkGsers about leaking rear brake cam.
So I will ask my other question here too.
What's the best way to replace leaking pushrod tube seals?
I am assuming I will have to replace the cylinder base gaskets and head gaskets also when I pull the cylinders off, or is it possible to remove the cyl without taking the head off?
There is not much info in Haynes or Clymer about this.
Any tips or tricks? Thanks, Peter
Reply With Quote
  #4  
Old 25 Jan 2005
Gold Member
Veteran HUBBer
  
Join Date: Mar 2001
Location: British Columbia
Posts: 246
It is pretty straight forward:
you will need to take the heads off (bolts run throught the heads to the block). As such, you will need a head gasket and the three o-rings for the cylinder base seal (2 small one Large, you should be able to get this all as a kit) for each side. Check your rocker cover gasket, if they are old they often rip on removal, I like to have at least one spare on hand.

The push rod seals are pretty easy but if you are replacing the push rod tubes as well then you have to take care to seat them properly, but not too deep. It is worth measuring the depth of the stock ones before you take them out.

Don't over torque the heads when you put them back on. This will not help in sealing a leak. If you have a leak it is likely that a o-ring has gotten munched as the cylinder slid back on. Last time I did this I used some heavy grease to hole the clyinder base o-ring in it's groove and keep it from catching a lip and getting munched - seemed to work well.

good luck!
Reply With Quote
  #5  
Old 25 Jan 2005
Grant Johnson's Avatar
HU Founder
Veteran HUBBer
  
Join Date: Dec 1997
Location: BC Canada
Posts: 7,226
Cameron, be especially careful NOT to overtorque the heads. There is a thread on the HUBB about head torque with the correct valuse. UNDERtorquing {b}slightly[/b] - see the thread for numbers - is worthwhile, as even correct torque can strip the threads in the crankcase. Nasty.

------------------
Grant Johnson

Seek, and ye shall find.
------------------------

One world, Two wheels.
www.HorizonsUnlimited.com
__________________
Grant Johnson
Seek, and ye shall find.
------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
Reply With Quote
  #6  
Old 25 Jan 2005
Contributing Member
Veteran HUBBer
  
Join Date: Jul 2002
Location: Sydney, NSW, Australia
Posts: 1,362
On the brake cam thing.

The groves on teh brake cam on my '81 G/S were not there for O rings - I had to have them machined out.

Later on bm placed a tube so that the brake cam shaft did not run in the bevel drive oil. On my K75C this tube measures 15.8mm OD 14.0mm ID 83.5mm length. It is a push fit into the housing - a little heat helps. This may be a better way of removing the leak. However even this has its problems - as th ehousing heats up the differential expansion can lead to leaks - a small bit of silastic is very helpfull to seal between the tube and housing.
__________________
---
Regards Frank Warner
motorcycles BMW R80 G/S 1981, BMW K11LT 1993, BMW K75 G/S
Reply With Quote
  #7  
Old 27 Jan 2005
Contributing Member
Veteran HUBBer
  
Join Date: Aug 2001
Location: B.C. Canada
Posts: 209
Thanks Guys,
You answered all my Questions. For a change I was looking for info BEFORE I pulled everthing apart and mucked something up.
I did know about overtorqing the heads, as out of four overlanding bmw's in Mr Yuts Bangkok shop, mine was the only one without pulled headstuds...
Timo, I have been using silicone valve cover gaskets from Real Gaskets for years now and they work very well. With care they will last forever, they don't leak, and are easy to take off and put back on. Good stuff, but not cheap. Cheers
Reply With Quote
  #8  
Old 27 Jan 2005
Gold Member
Veteran HUBBer
  
Join Date: Mar 2001
Location: British Columbia
Posts: 246
That's a good tip on the gaskets: I had heard about them years ago, but forgotten! To think of the many gaskets I've mangled since....
Reply With Quote
  #9  
Old 6 Feb 2005
Registered Users
Veteran HUBBer
  
Join Date: Sep 2002
Location: london,england
Posts: 186
simple (but not alwys permanent) fix for leaking pushrod tubes- tap the base toward the engine block with a hammer and bit o wood to reseat em....
Reply With Quote
  #10  
Old 7 Feb 2005
Contributing Member
Veteran HUBBer
  
Join Date: Jul 2002
Location: Sydney, NSW, Australia
Posts: 1,362
Tapingt th epushrod tubes to fix leaks DOES NOT WORK on newer boxers - I know it does not work on my 1980 R80 G/S for example.
__________________
---
Regards Frank Warner
motorcycles BMW R80 G/S 1981, BMW K11LT 1993, BMW K75 G/S
Reply With Quote
  #11  
Old 7 Feb 2005
Contributing Member
Veteran HUBBer
  
Join Date: Nov 2000
Location: Wirral,UK
Posts: 172
Hi

Speaking as one of the four at Yut's, I heartily advocate the use of appropriate torques!

How's your project going Peter?

Sean
__________________
Sean
Reply With Quote
  #12  
Old 9 Feb 2005
Contributing Member
Veteran HUBBer
  
Join Date: Aug 2001
Location: B.C. Canada
Posts: 209
Hi Sean,
My project is going slow and cheap (like me).
I rode the poor old G/S all last summer, just adding gas and oil instead of fixing it first. I am such a bad BMW owner...
Just now ordering seals and carb kit for much needed winter maintenance. The front brake project is ongoing ,with new ebc rotor and pads here ,but not installed yet.
Hoping to do some "more" serious testing this summer to see if this is really a going to be a good south america bike...
How are you making out with your bike...?Siebenrock solution perhaps...let us know

Skits, sorry for hijacking your question.
How are you making out with the cam leak?
I will not be getting to mine for a few weeks yet.
Cheers, Peter
Reply With Quote
  #13  
Old 9 Feb 2005
Contributing Member
Veteran HUBBer
  
Join Date: Nov 2000
Location: Wirral,UK
Posts: 172
Hi Peter

Bad BMW owner? Your R80 was one of the sweetest sounding I've ever heard!

But... Have to confess my poor old girl is still in a right state. I've just bought a house so funds to fix have been scarce over the winter. Still ridable around town if you don't mind the rattles and oily feet - just wouldn't use on a longer tour.

Siebenrock kit sounds good, but what about the need for higher octane fuel? I've found another low mileage 1996 1000cc mystic and am again thinking about a transplant....

Cheers

Sean
__________________
Sean
Reply With Quote
  #14  
Old 10 Feb 2005
Contributing Member
Veteran HUBBer
  
Join Date: Aug 2001
Location: B.C. Canada
Posts: 209
Hey Sean, How about the other way?
Will your tank fit the mystic and that great front end should be interchangable too...
Is that mystic higher geared??? you know you like the speed.....Cheers, Peter
Reply With Quote
  #15  
Old 10 Feb 2005
Registered Users
Veteran HUBBer
  
Join Date: Aug 2001
Location: Vancouver, BC - now at large in the world
Posts: 411
Cameron,

Where in YVR are you? I have an R80G/S I've rebuilt and can help you with things if needed.

Kevin

------------------
Kevin

http://www.nohorizons.net
__________________
http://www.nohorizons.net
Reply With Quote
Reply
Page 1 of 2 1 2

« Previous Thread | Next Thread »

Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

Your ad could be here, on EVERY page of the HUBB, or the whole website, or as many as you like!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.



All times are GMT +1. The time now is 23:58.

Contact Us - Horizons Unlimited Motorcycle Travellers Website - Archive - Privacy Statement - Top