Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > BMW Tech
BMW Tech BMW Tech Forum - For Questions specific and of interest to BMW riders only.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 19 Oct 2010
Registered Users
Veteran HUBBer
 
Join Date: Feb 2002
Location: Coimbra, Portugal
Posts: 321
BMW high compression ratio pistons (11.2:1)

Hello

I’m planning an expedition with a R100GS. The bike has high compression ratio pistons (11.2:1)

Will I have problems with sahara fuel? The normal pertol is 95 octant or lower?

I normally travel with diesel LRs so this problem never cross my mind

tks
__________________
bernardo feio (Portugal)
2.5 Land Rover Lightweight / BMW R80 G/S PD / Toyota HZJ 78
Reply With Quote
  #2  
Old 20 Oct 2010
Registered Users
Veteran HUBBer
 
Join Date: Oct 2002
Location: Stockholm - Sweden
Posts: 317
...are you really sure about that?

Do you have 4-valve technique on the airhead?

Above 10.5:1 on an airhead is pushing it... and above 11:1 is adviced against by all sources I have have found...

It is -not- possible to run on poor petrol with that high compression ratio... you should seriously consider changing to stock 9.5:1 or even the 8.2:1 version to minimise overheating risks and allow for usage of low and poor octane petrol... there is a reason for why the Egypt Police ordered a special version of the R80 engines... 44/40 valves with Bing 40... equates about 7:1 allowing for EU 87 octane petrol to be used...

Let us know -exactly- how your engine have been modified. It is possible that my comments above may not apply - it depends on exactly how the conversion to 11.2:1 have been made.
__________________
Drive Safely,
Albert
Reply With Quote
  #3  
Old 20 Oct 2010
AliBaba's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Apr 2001
Location: Norway
Posts: 1,379
Are you sure 11.2:1 is correct? I would have made a compression-test to check it.

Personally I would never used anything higher then 9.5:1 on bike intended for traveling in areas with poor fuel. It's probably a bit on the safe side but on the other hand you can get a very powerful engine with 9.5:1.



Quote:
Originally Posted by dc lindberg View Post
Let us know -exactly- how your engine have been modified. It is possible that my comments above may not apply - it depends on exactly how the conversion to 11.2:1 have been made.
Yes, please tell us!
Reply With Quote
  #4  
Old 20 Oct 2010
Registered Users
Veteran HUBBer
 
Join Date: Feb 2002
Location: Coimbra, Portugal
Posts: 321
hello

I have a normal 2 valve airhead and I need barrels (they have some scratches) and pistons + pistons rings

“It is -not- possible to run on poor petrol with that high compression ratio” I full agree with you if you keep the same combustion chamber shape.

http://www.moorespeed.co.uk/bmw-engine

High compression ratio pistons
Designed by Richard Moore in collaboration with Omega pistons, these high compression pistons offer the most cost-effective (and easiest) way to boost power. The dyno charts show the solid increase in both bhp and torque achieved simply by slipping in these new pistons (use your existing piston rings if in good condition) – an extra 8bhp for a couple of hours work! Combine them with a free-flowing Moorespeed air filter conversion, and gain an extra 2bhp (see also Moorespeed Tuning Kit section).”


I still don’t have the pistons installed but I have the same doubts that you have (that why I have I posted where)

Yesterday I called Richard Moore from moorespeed and I had a long talk with whim. He has a looong experience in motorsport and in BMWs air heads. He seems a very well formed fellow and not just a curious.

We said that his pistons here used in several African races with out problems. He also has some bikes that were used in Africa tours also without problems.

He says that eventually if the fuel is very low in octane level you should delay a bit the timing to avoid some knocking.


Personally I would never used anything higher then 9.5:1 on bike intended for traveling in areas with poor fuel. It's probably a bit on the safe side but on the other hand you can get a very powerful engine with 9.5:1.”


What solution do you use? Siebenrock replacement Kit?

thanks
__________________
bernardo feio (Portugal)
2.5 Land Rover Lightweight / BMW R80 G/S PD / Toyota HZJ 78
Reply With Quote
  #5  
Old 20 Oct 2010
AliBaba's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Apr 2001
Location: Norway
Posts: 1,379
I can't see that Richard Moore claims hat the pistons will give you 11.2:1 and I would have expected much better dyno-runs if they did.

There are some discussion about his pistons (and my old setup) here: Power piston kit - ::. UKGSer.com .::

Quote:
Originally Posted by bernardo feio lightweight View Post
What solution do you use? Siebenrock replacement Kit?
I used a Siebenrock upgrade kit (800cc -> 1000cc) and a few other modifications for 60kkm. The kit worked nice and will probably be re-used on my second R80.
Right now I use a setup based on narrow 1043cc cylinders (from Mahle/HPN). I spend quite some time thinking about what compression-ratio to choose before I ended up at 9.5:1.
The bigger bore increases the risk for pinging so I also installed dual-plugging.
Reply With Quote
  #6  
Old 20 Oct 2010
Registered Users
Veteran HUBBer
 
Join Date: Feb 2002
Location: Coimbra, Portugal
Posts: 321
Hello

The compression ratio of Richard M. pistons is not written in his web page but he told me that by email and confirmed that yesterday by phone.

“1043cc cylinders (from Mahle/HPN).”

Can you give me more information about that? Part numbers, piston rings, prices…

If you prefer please send me a PM to:

bernardofeio @ yahoo.com.br

thanks
__________________
bernardo feio (Portugal)
2.5 Land Rover Lightweight / BMW R80 G/S PD / Toyota HZJ 78
Reply With Quote
  #7  
Old 20 Oct 2010
Registered Users
Veteran HUBBer
 
Join Date: Feb 2002
Location: Coimbra, Portugal
Posts: 321
BTW:

any comments on this kit?

[url=http://www.motoren-israel.com/products/en/Shop/Engine/Cylinderkit/Sportkitt-1000cc-75mm-kuerzer-MADE-IN-GERMANY.html]Sportkitt 1000cc, 7.5mm k
__________________
bernardo feio (Portugal)
2.5 Land Rover Lightweight / BMW R80 G/S PD / Toyota HZJ 78
Reply With Quote
  #8  
Old 20 Oct 2010
Registered Users
Veteran HUBBer
 
Join Date: Oct 2002
Location: Stockholm - Sweden
Posts: 317
Mr. Moore may be a excellent engineer, or a good con artist...
His site looks so much like the old catalogues from Luftmeister and CC in California... The pistons do look very smart. Keihan carbs - quite interesting. I will study his site later - my curiosity have been awakened

What is your budget?
How much may the conversion set you back (cost)?
=> gives us an idea of what to suggest, recommend and advice about.


If you want to play it as safe as possible, I would recommend that you get a set of 8.2:1 BMW original pistons with squissband (those perform just a little bit better than those without, in my opinion).
Perhaps you will have to buy pistons for steel-lined barrels and pistonrings for the nicasil barrels that your model have; that's how I had to solve high-compression on the 800-system. Works nicely - no problem.

Currently I am running 1000cc replacement Siebenrock pistons - love them.
But (!) - that is 9.5:1 and as I pointed out above; I would recommend that you do not choose the high-compression solution.
The Siebenrock pistons are about 50gr lighter than my Velonlia 10.5:1 pistons. The Venolia pistons are about 70gr lighter than stock (if I recall correctly) - and runns very smoothly once warm; far nicer than the heavy lumpy unbalanced original pistons.
If you go with 8.2:1 original pistons - balance them (!) and the conrods => the engine runns far better if you do.



Should you want high-compression - study carefully what Alibaba and Mr.MR writes!

My personal experience with high-compression is; good power, good mileage, a ... lot of garage time and heachache figuring out what broke and why. Since I ride in an area where high-octane petrol is available I want the high-compression; but should I ride in areas with questionable petrol, well... I would study closely how the Egyptian Police set up their special R80's!!!

Remeber - as compression raises... so does engine heat... The mileage differens is not -that- great that I would sacrifice/risk durability...


Good - to excellent engine/oil cooling should be your focus as well as looking at the most optimal solutions for keeping the engine running.

The hall-sensor pick-up (ITU) is a source of concern. The braker-point canister used on the late 70:ties models may be an option to consider. Braker points take little room, a spare hallsensor-canister is kind of bulky and difficult to mend on the road. I read here on H.U. about a year ago about this tip on the braker-point option - if I recall correctly VW 1200 (beetle) braker-points fits. You need to check that though - I might remeber it in-correctly.

If you want more power... you could install a turbo or super charger...
Seriosly - keep everything as light as possible and as close to stock as possible, or rather "retro-convert" to more simple and easy solutions for best road-side repairability.
*
Apply KISS strategy; "keep it simple stupid" - That will save you from a lot of trouble and headache
__________________
Drive Safely,
Albert
Reply With Quote
  #9  
Old 20 Oct 2010
Registered Users
Veteran HUBBer
 
Join Date: Feb 2002
Location: Coimbra, Portugal
Posts: 321
Quote:
Originally Posted by dc lindberg View Post
Mr. Moore may be a excellent engineer, or a good con artist...
Quote:
Originally Posted by dc lindberg View Post
His site looks so much like the old catalogues from Luftmeister and CC in California... The pistons do look very smart. Keihan carbs - quite interesting. I will study his site later - my curiosity have been awakened

Quote:
Originally Posted by dc lindberg View Post
What is your budget?
How much may the conversion set you back (cost)?
=> gives us an idea of what to suggest, recommend and advice about.



600 euros?... but I also need some barrels (can be used)

Quote:
Originally Posted by dc lindberg View Post
My personal experience with high-compression is; good power, good mileage, a ... lot of garage time and heachache figuring out what broke and why. Since I ride in an area where high-octane petrol is available I want the high-compression; but should I ride in areas with questionable petrol, well... I would study closely how the Egyptian Police set up their special R80's!!!



Quote:
Originally Posted by dc lindberg View Post
looking at the most optimal solutions for keeping the engine running.


? I didn't understand you now...


Quote:
Originally Posted by dc lindberg View Post
The hall-sensor pick-up (ITU) is a source of concern. The braker-point canister used on the late 70:ties models may be an option to consider. Braker points take little room, a spare hallsensor-canister is kind of bulky and difficult to mend on the road. I read here on H.U. about a year ago about this tip on the braker-point option - if I recall correctly VW 1200 (beetle) braker-points fits. You need to check that though - I might remeber it in-correctly.


braker-point canister?... what is that? I also didn’t understand you on this…

Quote:
Originally Posted by dc lindberg View Post
Apply KISS strategy; "keep it simple stupid" - That will save you from a lot of trouble and headache


That I use almost always. If you look to my signature you will notice what kind of vehicles I use in my expeditions.... very simple and basic

thanks for your very interesting answer...
__________________
bernardo feio (Portugal)
2.5 Land Rover Lightweight / BMW R80 G/S PD / Toyota HZJ 78
Reply With Quote
  #10  
Old 21 Oct 2010
AliBaba's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Apr 2001
Location: Norway
Posts: 1,379
The kit from Motoren Israel will set you back around 950€.
It's 699€ for the kit, 55€ for the pushrod-tubes, 15€ for inserting the pushrod-tubes, 75€ for the pushrods, 45€ for bolts and 35€ for the gaskets.


The kit is from Mahle and usually their products are nice. I have no experience with the kit but I do have some experience with Motoren Israel.
It might be a smart idea to get in touch with them and tell them what you are looking for. Silvia is a friendly guy and he has given me many good advices through the years.

Lindberg mentions heat as a possible problem with a modified engine and he might have a point here. The problem with air-cooled engines is that there is not much cooling when you ride really slow (technical sections or rush-hour). This is not a major concern for equipment used under racing-conditions because they keep the speed up and gets better air-flow.
My bike ran hotter with the modified Siebenrock-setup and an oilcooler then it did as a stock R80 (without a cooler), but it never gave me any kind of problems.
Reply With Quote
  #11  
Old 21 Oct 2010
Registered Users
Veteran HUBBer
 
Join Date: Feb 2002
Location: Coimbra, Portugal
Posts: 321
Hello

Thanks for your answer Alibaba. Your comments are very important because of your African travel experience with these bikes!

Does any one know what are the power/torque claims for the Moto Israel 112011 piston kit 1000cc -7,5mm



__________________
bernardo feio (Portugal)
2.5 Land Rover Lightweight / BMW R80 G/S PD / Toyota HZJ 78
Reply With Quote
  #12  
Old 22 Oct 2010
AliBaba's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Apr 2001
Location: Norway
Posts: 1,379
Quote:
Originally Posted by bernardo feio lightweight View Post
Does any one know what are the power/torque claims for the Moto Israel 112011 piston kit 1000cc -7,5mm
You can ask Silvia at Motoren Israel but I don't think he will know.
Usually people change a lot in their engines when they rebuild it so it's hard to tell..
Reply With Quote
  #13  
Old 31 Oct 2010
Registered Users
Veteran HUBBer
 
Join Date: Oct 2002
Location: Stockholm - Sweden
Posts: 317
I just studied Mr Moores homepage/Dyna test.
Technical

THAT I did miss reading from the beginning.
I am NOT one bit impressed!
60bhp and 6kg torque - on a 1000cc engine?!
I do see notions of 66bhp and 7.6(?)kg torque - but it is very hard to read his test papers (too low resolution).

Anyway, you do get FAR more power by simply installing stock 9.5:1 pistons and old 44/40 valve heads with bing 40. That should give you 67-70bhp and about 7.4kg torque.
And he is asking 400 EU for such a "crappy" kit?!

With the low compression pistons: 8.2:1 and bing 40 you should have 60-65bhp, and about 7kg torque.

38mm exhaust. 40mm exhaust does not give you more power, rather you loose a bit of lowend torque.

11:1 would theoretically give you about 80bhp and close to 8kg torque - but to be sure you need to test it.

1100cc kit from 7-stones or the tunings done by Motoren Israel will give you >>80bhp. Those who have that kit describe it as -powerful- and -fun- to drive.
__________________
Drive Safely,
Albert
Reply With Quote
  #14  
Old 1 Nov 2010
AliBaba's Avatar
Registered Users
Veteran HUBBer
 
Join Date: Apr 2001
Location: Norway
Posts: 1,379
If you click at the graphs you will get better resolution.
He claims:

Standard R100: 51bhp/ 47Ft/lb (64Nm)
Omega long skirt: 58bhp / 53Ft/lb (72Nm)
Omega long skirt with different filters: 60bhp/ 55Ft/lb (75Nm)
Omega with long rods: 63bhp / 57FT/lb (77Nm)

I think the numbers for a standard R100 looks about right. Like you I'm not impressed by the results for the Omega pistons, with such an increase in compression I would have expected more.
Reply With Quote
  #15  
Old 1 Nov 2010
Registered Users
Veteran HUBBer
 
Join Date: Feb 2002
Location: Coimbra, Portugal
Posts: 321
hello

thanks for all the comments.

For now I will put the 11:1 pistons in standby. I'm still not sure if I will have problems with low octane fuel with this solution.

BTW: last May I went to Algeria with my lightweight and with a friend with a modified KTM. The KTM was using an engine with 11.5:1 compression and he didn't have any problems with pinging. Only overheating… J

I will probably go moto Israel solutions but I would like to see some Dyna tests and find more comments about them.

Bernaro Feio



__________________
bernardo feio (Portugal)
2.5 Land Rover Lightweight / BMW R80 G/S PD / Toyota HZJ 78
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 2 (0 Registered Users and/or Members and 2 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
High Compression Problems Micah Yamaha Tech 5 12 Jun 2011 13:57
xr compression ratio q's benmh Honda Tech 1 28 Sep 2010 20:34
TS185 ER compression ratio jcarlin123 Suzuki Tech 7 25 Jul 2009 07:36
Coolant mix Ratio PatOnTrip Equipment Reviews 2 18 Aug 2004 08:36
Wiseco pistons david lambeth Yamaha Tech 5 17 Oct 2002 09:03

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 10:08.