Go Back   Horizons Unlimited - The HUBB > Technical, Bike forums > BMW Tech
BMW Tech BMW Tech Forum - For Questions specific and of interest to BMW riders only.
Photo by Daniel Rintz, Himba children, Namibia

The only impossible journey
is the one
you never begin

Photo by Daniel Rintz,
Himba children, Namibia



Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 23 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Jul 2008
Location: Aussie expat in Switzerland half way RTW
Posts: 611
Exclamation ABS issue on 1200GS

So after several weeks of troubleshooting an ABS problem with my 1200GS I thought I'd post a summary of the issues and the final solution here in case it can help anyone else.

Background:
I've got just under 70,000kms on the bike
2007 Model BMW 1200GS
ABS version II
We have ridden all terrain, not just road.
I use the GS-911 diagnostic unit connected to my WM5 HP iPaq phone.
The ABS issue occured just after another error with the wheel speed sensor (41445 I think).

Error reported by GS-911:
10220: Can-bus timeout: no communication with ABS control unit.

Symptoms:
Brake Failure warning light on the Dashboard.
ABS doesn't work.
No speedo.
No odometer (ie. no distance travelled is recorded at all, counter stays at zero)

Inspections and repairs:
There are no issues with FD (yet) checked play on rear bearings.
There are no metal shards or filings in the FD oil.
The battery was dead so I have replaced the battery.
I have inspected both front and rear wheel speed sensors. The rear looked damaged by heat and so I replaced it.
The bike runs fine apart from the Brake Failure warning light.
The Dash works fine, ie clock, fuel indicator revs and oil temp all work fine.

The brake fluid was changed (supposedly) last year (under 20,000kms). BMW recommends every 2 years of 20,000kms. So I can't see why this should be a problem.

As a result of the constant brake failure, my rear brake light didn't work when activated by either front or rear brakes. IMO This is very dangerous. All the other problems linked to the ABS failure are ok and means the bike is ridable but no brake lights are for me a critical saftey issue.

I had run out of options so started calling BMW mechanics to get their input, I finally resorted to taking it into a BMW repair shop and they diagnosed using the BMW diagnostic unit. I didn't get the exact read out but it was something along the line that the ABS pump failed and could not be re-initialised. The mechanic I told me he tried to reset/flash the ABS unit but this didn't help.

The Mechanic didn't try to bleed the circuit but I think it probably was too late if the ABS had already completely failed...

Bottom line:
ABS is toast. I need a new ABS pump. This part is $1700.

The Mechanic is also doing a couple of recalls on my bike at the same time. I'll let you know the pain when I get the bike back, but it's likely to be over $2000...
__________________
TurboCharger + Francois (our BMW R1200gs) '07
www.riding2up.net, blog.riding2up.net
Reply With Quote
  #2  
Old 23 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Apr 2008
Location: West Yorkshire UK
Posts: 1,785
Not that this will help, but the diagnostic process and error code descriptions make perfect sense, which isn't always the case.

Who changed the brake fluid? If a dealer was involved, introduce the idea that they may have powered the system up with the ABS unit dry. The brake fluid lubes the ABS unit, so if they had run it dry some sort of contribution might be in order.

No ones done any welding or jump starting have they? Ten years of handling warranty claims on ABS bits and these two pop up time and time again as the single most effective way to cause this sort of issue.

Andy
Reply With Quote
  #3  
Old 23 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Jul 2008
Location: Aussie expat in Switzerland half way RTW
Posts: 611
Quote:
Originally Posted by Threewheelbonnie View Post
Not that this will help, but the diagnostic process and error code descriptions make perfect sense, which isn't always the case.

Who changed the brake fluid? If a dealer was involved, introduce the idea that they may have powered the system up with the ABS unit dry. The brake fluid lubes the ABS unit, so if they had run it dry some sort of contribution might be in order.

No ones done any welding or jump starting have they? Ten years of handling warranty claims on ABS bits and these two pop up time and time again as the single most effective way to cause this sort of issue.

Andy
Hi Andy,

Thanks for the reply. Unfortunately I already asked BMW to contribute and they said no. I don't really have a leg to stand on although I'm very peeved about the ABS failure. Basically I think that the ABS fluid when changed was over a year ago and the dealer is no longer handling BMW anymore so not going to help my cause.

Oh and no welding or any jump starting has been done on the bike. Although now that you mention it, I did short the battery to the frame when I was swapping out the old battery, there was a spark. Do you think that is could have triggered the ABS unit to fail?? I would be very surprised and would like to know more if you think it could be the cause...

Cheers
Pascal
__________________
TurboCharger + Francois (our BMW R1200gs) '07
www.riding2up.net, blog.riding2up.net
Reply With Quote
  #4  
Old 23 Aug 2011
strimstrum's Avatar
Gold Member
Veteran HUBBer
 
Join Date: Aug 2008
Location: Alcester UK & Idilevo, Bulgaria
Posts: 329
Pascal

I have a 2007 1200GS which has just completed a RTW with no problems so your problem is of interest to me. A rather stupid question possibly....... but if you turn off the ABS do the brake lights work then bearing in mind you have overridden the pat of the bike causing the problem ?

Martin
Reply With Quote
  #5  
Old 24 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Jul 2008
Location: Aussie expat in Switzerland half way RTW
Posts: 611
Hi Martin,

The ABS failure caused the ABS to be off all the time so it was not possible to toggle the ABS (with the ABS button on the handlebar) during the failure.

On a bike with working ABS if you toggle the ABS off then the brake lights will work. They should always work, but check this, if not then you have a problem.

The problem with my bike and the ABS failure is that the error code (10220 when interrogated with GS-911 diagnostic tool) said that the CANbus didn't communicate to the ABS unit, it just timed out. The CANbus interpreted this as a brake failure so failed to interpret the brake switch activation on front and rear of the bike. Again all this was related the the ABS failure.

End result of all this complex ABS integration meant:
  • no odometer
  • no speedo
  • no brake light
  • and of course no ABS
IMHO this is a poor and very dangerous design, to have speedo and especially brake light dependent on the ABS unit.

Cheers,
Pascal
__________________
TurboCharger + Francois (our BMW R1200gs) '07
www.riding2up.net, blog.riding2up.net
Reply With Quote
  #6  
Old 24 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Jul 2008
Location: Aussie expat in Switzerland half way RTW
Posts: 611
On a final note, and as I've seen recommended on other forums and was recommended by multiple BMW mechanics, the ABS needs regular
maintenance. It also needs to be used. Some suggest applying ABS on a
semi-regular basis (ie. going downhill on loose surface or on wet grass) to ensure the ABS unit is exercised. Also I have been recommended to change and bleed the entire brake fluid at least every 2 years or 20,000kms as a minimum. I will do this more often now as it is a lot cheaper than a new ABS!!!
__________________
TurboCharger + Francois (our BMW R1200gs) '07
www.riding2up.net, blog.riding2up.net
Reply With Quote
  #7  
Old 24 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Apr 2008
Location: West Yorkshire UK
Posts: 1,785
IMHO the odd spark/short shouldn't do any harm, but if you combine it with a bad bit of soldering on the production line or the last percentile component in the quality range it might be enough to send it over the edge.

The "exercise your ABS" plan is utter guff. The ABS does a full self test valve cycle at each ignition on (the clunk click as the lights change sequence on the older systems, more subtle on later ones) and partially energises the solenoids every few seconds to confirm they are electrically OK. Deliberately cycling the ABS on wet grass (a surface it is not designed for) is only good for sales of new body panels, levers, mirrors and medical insurance.

Changing the brake fluid as required is a good plan to get water out. Don't do it too often and leave the ignition off until you have a fully bled and working hydraulic set up, the fluid lubes the pump and valves.

The routing of the brake lights via the ABS ECU is highly suspect IMHO. The whole point of CAN is to utilise the info you have over the whole network, so telling the ABS to "wake up" via the brake light change of state is a good use that will improve its reactions. The fact is though that this signal can be picked up via the general network, the ABS can be a "listener" without having any direct input. Strikes me that the boys in Munich ran out of capacity on the instrument module and rather than expanding it decided to put the brake light reaction into the ABS ECU. Running the actual brake light wires a whopping 1 meter less saved them something too. I understand such logic on a bendy bus or a truck with potential road train uses, but on a 2m long bike it's ridiculous corner cutting.

Andy
Reply With Quote
  #8  
Old 24 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Jul 2008
Location: Aussie expat in Switzerland half way RTW
Posts: 611
Quote:
Originally Posted by Threewheelbonnie View Post
IMHO the odd spark/short shouldn't do any harm, but if you combine it with a bad bit of soldering on the production line or the last percentile component in the quality range it might be enough to send it over the edge.
Mmm, not convinced but you are quite possibly right even if I want to deny it.

Quote:
Originally Posted by Threewheelbonnie View Post
The "exercise your ABS" plan is utter guff. The ABS does a full self test valve cycle at each ignition on (the clunk click as the lights change sequence on the older systems, more subtle on later ones) and partially energises the solenoids every few seconds to confirm they are electrically OK. Deliberately cycling the ABS on wet grass (a surface it is not designed for) is only good for sales of new body panels, levers, mirrors and medical insurance.
Agree with your sentiment and the technical aspect makes sense but what would you say about old brake fluid becoming (more) corrosive and detroying ABS filters?

Quote:
Originally Posted by Threewheelbonnie View Post
Changing the brake fluid as required is a good plan to get water out. Don't do it too often and leave the ignition off until you have a fully bled and working hydraulic set up, the fluid lubes the pump and valves.
So do you think that brake fluid goes bad (ie corrosive and detroying seals or filters) or not? Could this be the cause of the ABS failure?

Quote:
Originally Posted by Threewheelbonnie View Post
The routing of the brake lights via the ABS ECU is highly suspect IMHO. The whole point of CAN is to utilise the info you have over the whole network, so telling the ABS to "wake up" via the brake light change of state is a good use that will improve its reactions. The fact is though that this signal can be picked up via the general network, the ABS can be a "listener" without having any direct input. Strikes me that the boys in Munich ran out of capacity on the instrument module and rather than expanding it decided to put the brake light reaction into the ABS ECU. Running the actual brake light wires a whopping 1 meter less saved them something too. I understand such logic on a bendy bus or a truck with potential road train uses, but on a 2m long bike it's ridiculous corner cutting.

Andy
I pulled up stumps on this one. No idea what would posses them to have such a dependency - makes no sense at all to me.
__________________
TurboCharger + Francois (our BMW R1200gs) '07
www.riding2up.net, blog.riding2up.net
Reply With Quote
  #9  
Old 24 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Apr 2008
Location: West Yorkshire UK
Posts: 1,785
Brake fluid is hydroscopic, it absorbes water. This is bad for two reasons; first of all if you heat it by getting close to the rubbing surface and change pressure with the brake cylinders it turn to steam which is compressible and therefore allows the pads to drop back. The brake feels spongy. Secondly, if left to settle out the water will accumulate at surfaces such as o-ring grooves. As these are made of alloy and often have air on the other side they rot and fur up blocking the small passageways. There are no filters on any hydraulic ABS system I ever worked on although my work with BMW was very short and limited to 4x4's.

I can't remember the numbers, but the absorbtion of water constantly increases through the fluids life. At two years the change is measurable on the standard tests, hence thats when the manufacturers want to sell you more. At five years you'll see furry valves and no doubt feel the effects. Between the two is between the two and will of course vary with how the vehicle is used, where it is etc. I buy the brake fluid at two years and it gets changed at the next engine oil service or before the next trip.

Andy
Reply With Quote
  #10  
Old 25 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Jul 2008
Location: Aussie expat in Switzerland half way RTW
Posts: 611
Thumbs up

Got the bike back today and I'm happy to say all my problems have gone away!!

Thanks to the team at Motos Vionnet.

(No I'm not paid for the plug and I didn't even get a discount )
__________________
TurboCharger + Francois (our BMW R1200gs) '07
www.riding2up.net, blog.riding2up.net
Reply With Quote
  #11  
Old 25 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Mar 2007
Location: UK
Posts: 4,343
Quote:
Originally Posted by TurboCharger View Post
Got the bike back today and I'm happy to say all my problems have gone away!!

Thanks to the team at Motos Vionnet.

(No I'm not paid for the plug and I didn't even get a discount )
Any insights about the final diagnosis of the ABS pump? Did it fail due to fair wear and tear/old age (2007 bike) or is there any better insight?
Just being curious about your useful, but expensive, experience.

Thanks to 3Wbonnie for clearing up some technical issues, including the lack of filters in ABS systems (I was wondering about that!).
__________________
Dave
Reply With Quote
  #12  
Old 25 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Apr 2008
Location: West Yorkshire UK
Posts: 1,785
Glad you are up and running.

Andy
Reply With Quote
  #13  
Old 25 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Jul 2008
Location: Aussie expat in Switzerland half way RTW
Posts: 611
Quote:
Originally Posted by Walkabout View Post
Any insights about the final diagnosis of the ABS pump? Did it fail due to fair wear and tear/old age (2007 bike) or is there any better insight?
Just being curious about your useful, but expensive, experience.

Thanks to 3Wbonnie for clearing up some technical issues, including the lack of filters in ABS systems (I was wondering about that!).
Unfortunately the short answer is no. The mechanic may not be experienced enough or perhaps it's more the fault of BMW that makes the ABS unit a non-servicable part.

The bottom line here is ensure your brake fluid must be changed every 2 years and the full brake circuit is bled.
__________________
TurboCharger + Francois (our BMW R1200gs) '07
www.riding2up.net, blog.riding2up.net
Reply With Quote
  #14  
Old 25 Aug 2011
Registered Users
Veteran HUBBer
 
Join Date: Apr 2008
Location: West Yorkshire UK
Posts: 1,785
The ABS unit is assembled in close to clean room conditions and contains many small parts, a lot of them press fit. The hydraulic units I'm most familiar with (Landrover) were supplied as only two part numbers; complete ABS unit wet and complete ABS unit dry. The only difference was that the wet one was easier to bleed (all the nooks and crannies filled with fluid) and the dry one could be sent air freight. Dealer service techs were not expected to do anything except change the whole unit. It isn't any lack of skill on the part of a lot of techies, it's how the things are designed with input from the lawyers and parts department accountants.

Andy
Reply With Quote
  #15  
Old 25 Aug 2011
strimstrum's Avatar
Gold Member
Veteran HUBBer
 
Join Date: Aug 2008
Location: Alcester UK & Idilevo, Bulgaria
Posts: 329
Quote:
Originally Posted by TurboCharger View Post
Hi Martin,

The ABS failure caused the ABS to be off all the time so it was not possible to toggle the ABS (with the ABS button on the handlebar) during the failure.

On a bike with working ABS if you toggle the ABS off then the brake lights will work. They should always work, but check this, if not then you have a problem.

The problem with my bike and the ABS failure is that the error code (10220 when interrogated with GS-911 diagnostic tool) said that the CANbus didn't communicate to the ABS unit, it just timed out. The CANbus interpreted this as a brake failure so failed to interpret the brake switch activation on front and rear of the bike. Again all this was related the the ABS failure.

End result of all this complex ABS integration meant:
  • no odometer
  • no speedo
  • no brake light
  • and of course no ABS
IMHO this is a poor and very dangerous design, to have speedo and especially brake light dependent on the ABS unit.

Cheers,
Pascal
Thanks for the heads up Pascal - I am pleased that you are up and running and now I think it may be time to change my brake fluid !

Also Thanks to ThreewheeledBonnie for your input.

Martin
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
21" Rim for 1200gs? mcdarbyfeast BMW Tech 13 23 Aug 2011 13:51
where is the best/low price bmw 1200gs/A malimimi Travellers' Advisories, Safety and Security on the Road 0 28 Nov 2009 18:38
1200GS cutting out Tim Cullis BMW Tech 8 17 Jul 2008 13:56
maintenance for 1200GS $$$$$???? J. Cadena BMW Tech 6 4 Dec 2005 03:48

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

HU Event and other updates on the HUBB Forum "Traveller's Advisories" thread.
ALL Dates subject to change.

2024:

Add yourself to the Updates List for each event!

Questions about an event? Ask here

HUBBUK: info

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 14:01.